Manual Jotul F 374 (page 14 of 104) (English, Dutch, French, Italian, Spanish)

467801

Zoom out

Zoom in

1/104

Jøtul F 379 - with three legs

NB! If connecting the flex hose through a hole in the floor, do not

knock out the removable cover plates (fig. 21 A).

Fig. 21

1. If connecting a flex hose (Ø 100 mm) for external air supply

to the external air vent (fig. 4 C) beneath the burn chamber,

first drill a hole (fig. 21 A) in the removable cover plates before

they are knocked out. NB! Place the parts on a suitable surface

before the cover plates are knocked out.

Fig. 22

2. The accompanying heat shield (fig. 22 A) should be used to

protect the base from the heat radiating from the product.

Secure this first with a screw (fig. 22 B).

3. Secure the brace (fig. 22 C) loosely into place with a screw

(fig. 22 D).

4. Attach the base to the burn chamber using the 4 screws

(M8 x 30 mm) from the bag of screws (fig. 4 A).

5. Screw the legs together at the back edge using 2 screws that

are in the screw holes (fig. 22 E).

6. Secure the brace (fig. 22 C) into place with a screw (fig. 22 F)

and nut at both ends.

7. With the help of another person, carefully raise the product.

8. Level the product using the 4 adjustment screws (fig. 22 G).

9. If the legs are not properly aligned, loosen the screws (fig. 22 F)

on each side. Adjust the legs and tighten the screws again.

10. Tighten the screw (fig. 22 D).

11. Pull the flex hose through the hole and attach it to the outlet

using a hose clip. NB! Make sure the hose is long enough so

that joints are not necessary.

Fig. 23

12. Place the cover (fig. 23 A) into place. Make sure that the pin

(protrusion) B is facing down.

4.3 Chimneys and flue pipes

• The fireplace can be connected to a chimney and flue

pipe approved for solid fuel fired appliances with flue gas

temperatures specified in «2.0 Technical data”.

• The chimney’s cross-section must be at least as big as the

flue pipe’s cross-section. See «2.0 Technical data» when

calculating the correct chimney cross-section.

• Several solid fuel fired appliances can be connected to the

same chimney if the chimney’s cross-section is sufficient.

• Connection to the chimney must be carried out in accordance with

the installation instructions from the supplier of the chimney.

• Before making a hole in the chimney the fireplace should be

test-mounted in order to correctly mark the position of the

fireplace and the hole in the chimney. See fig. 1 for minimum

dimensions.

• Ensure that the flue pipe is inclined all the way up to the chimney.

• Use a flue pipe bend with a sweeping hatch that allows it to

be swept.

Be aware of the fact that it is particularly important that

connections have a certain flexibility in order to prevent

movement in the installation leading to cracks.

Chimney draught; See «2.0 Technical data». If the draught is

too strong you can install and operate a flue damper to control

the draught.

Assembly of flue pipe with top outlet

The product is supplied from the factory with the smoke outlet

mounted for top outlet.

1. Put the top plate (fig. 3 C) on the product.

2. Obtain assistance in lifting the top grate (fig. 3 A) and holding

it up while the flue is fastened.

3. Thread the flue pipe through the grate of the top plate and

place it on the smoke outlet of the top outlet.

4. Tighten well with gasket.

ENGLISH

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jotul F 374 in the language / languages: English, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jotul F 374 Manual

Product: