Manual Jotul F 134 (page 22 of 72) (English, Dutch, French)

657937

Zoom out

Zoom in

1/72

Jøtul F 130 has a nominal heat output of ca. 4,7 kW. Use of

wood, with nominal heat emission: Approx. 1,25 kg/h. Another

important factor for proper fuel consumption is that the logs

are the correct size. The size of the logs should be:

Kindling:

Length: Max. 20 cm

Diameter: 2 - 4 cm

Amount per ﬁ re: 6 - 8 stk.

Firewood (split logs):

Diameter: Approx. 8 cm

Intervals for adding wood: Approximately every 45minutes

Amount per load: 1,25 kg (nominal heat output)

Size of the ﬁ re: 2 pieces

Amount per load: 1,26 kg

Nominal heat output is achieved when the ignition vent is open

approximately 30 % (ﬁ g. 28). Max. heat output is achieved

when the air vent is open 100 %.

6.0 Maintenance

6.1 Cleaning the glass

The product is equipped with an air wash for the glass. Air is

sucked in through the air vent on the top of the product and

down along the inside of the glass.

However, some soot will always stick to the glass, but the

quantity will depend on the local draught conditions and

adjustment of the air vent. Most of the soot layer will normally

be burned off when the air vent is opened all the way and a ﬁ re

is burning briskly in the ﬁ replace.

Good advice! For normal cleaning, moisten a paper towel

with warm water and add some ash from the burn chamber.

Rub it over the glass and then clean the glass with clean water.

Dry well. If it is necessary to clean the glass more thoroughly

we recommend using a glass cleaner (follow the instructions

on the bottle).

6.2 Cleaning and soot removal

Soot deposits may build up on the internal surfaces of the

ﬁ replace during use. Soot is a good insulator and will therefore

reduce the ﬁ replace’s heat output. If soot deposits accumulate

when using the product, they can be easily removed by using

a soot remover.

In order to prevent a water and tar layer from forming in the

ﬁ replace you should regularly allow the ﬁ re to burn hot in order

to remove the layer. An annual internal cleaning is necessary

to get the best heating effect from the product. It is a good idea

to do this in connection with the sweeping of the chimney and

ﬂ ue pipes.

6.3 Sweeping of ﬂ ue pipes to the

chimney

On certain free-standing ﬁ replaces the top plate can be lifted

off and the pipe swept through the top.

Otherwise, ﬂ ue pipes must be swept through the ﬂ ue pipe

sweeping hatch or through the product’s door opening. Then,

the bafﬂ e must be removed.

6.4 Inspection of the ﬁ replace

Jøtul recommends that you personally inspect your ﬁ replace

carefully after sweeping/cleaning. Check all visible surfaces

for cracks. Also check that all joints are sealed and that the

gaskets are in the correct position. Any gaskets showing signs

of wear or deformation must be replaced.

Thoroughly clean the gasket grooves, apply ceramic glue

(available from your local Jøtul dealer), and press the gasket

well into place. The joint will dry quickly.

6.5 Exterior maintenance

Painted products may change colour after several years usage.

The surface should be cleaned and brushed free of any loose

particles before new paint is applied.

Important! Never place anything on the top plate of the

stove. This could cause permanent damage to the paint

or enamel.

ENGLISH

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jotul F 134 in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 7,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jotul F 134 Manual

Product: