Manual Joovy Tricycoo 0017X (page 3 of 12) (English, French, Spanish)

781059

Zoom out

Zoom in

1/12

EN FR ES

!WARNING

Adult assembly required. Tools required (not included): Phillips Screwdriver. Choking Hazard to children under the

ageof3years–containssmallpartspriortoassembly.Somescrewsmayhavesharpedgesandsharppoints.

Keep all small parts out of reach of children at all times.

2 Installing the Rear Wheels

• Keep children away while assembling.

• Insert an Inner Rear Wheel Hub into either end of the rear axle cylinder on the rear of the tricycle frame. See Figure 1.

• Insert the axle into one of the rear wheels (ensuring that the side with the 8 holes faces out). Slide the axle (with the Rear Wheel) through

the Inner Rear Wheel Hub and the rear axle cylinder. See Figure 2.

• Insert the other Inner Rear Wheel Hub into the opposite end of the rear axle cylinder.

• Slide the other Rear Wheel over the axle (ensuring that the side with the 8 holes is facing out). Slide the large washer over the axle.

• Insertthesnappinstraightlegintothesmallholeintheaxle.Pushitrmlyintothisholeuntiltheroundportionoftheotherlegsnaps

completely around the outside of the axle. See Figure 3.

NOTE: The snap pin is curved (concave) to make insertion easier.

• Install a hubcap onto each wheel by aligning the 4 tabs with the 4 slots in the wheel. Ensure that ALL 4 tabs have engaged securely

and the hubcaps cannot be pulled off. See Figure 4.

3 Front Wheel Assembly

• Place the fender onto the front wheel tube making sure you push the fender all the way down. See Figure 5.

• With the long part of the fender facing forward insert the front wheel tube into the front steering hub of the tricycle frame. See Figure 5.

• Identify the 2 piece spacer (assemble if necessary) and slide it over the top of the front wheel set. Make sure to push the spacer all the

way down. See Figure 6.

IMPORTANT NOTE:

If you intend to use the optional baby surround system, slide the baby surround connector onto the tricycle frame.

See Figure 7. If not using the baby surround system then disregard this NOTE.

4 Handlebar Assembly

NOTE: If not using the baby surround system, make sure that the baby surround connector is NOT attached to the tricycle frame.

• Insert the handlebar onto the front wheel tube. See Figure 8.

NOTE: The handlebars should be mounted with the bars leaning forward.

• From the front of the product, insert the handlebar bolt (short) into the middle hole of the handlebar column and push it all the way

through. Attach the Nylock nut to the bolt and tighten using the tool provided. See Figure 9.

• Fit the front half of the handlebar cap through the bottom hole on the front of the handlebar.

• Snap the back half of the handlebar cap to the front. Secure the handlebar caps with the pointed Phillips head screw. See Figure 10.

NOTE: Pull on the handlebar and the handlebar caps to make sure they are secure.

5 Seat Assembly

• Place the seat onto the frame facing forward and line up the hole in the tricycle frame. See Figure 11.

• Secure the seat with the small washer, the lock washer, and the seat bolt (long). Tighten the screw securely. See Figure 12.

• Pull on the seat to ensure that it is secure.

6 Push Handle Assembly

• Place the basket onto the rear of the tricycle frame with the opening over the rear steering tube. See Figure 13.

• Next place the cover cap onto the rear steering tube. See Figure 14.

• Insert the upper half of the push handle into the end of the lower handle tube that has the plastic knob on it. Insert it so that the pin on the

upper handle is aligned with the holes in the lower tube and push down until a click is heard and the pin can be seen protruding from one

of the holes. Pull on the upper half to be sure it is secure. See Figure 15. For push handle adjustment, see Section 11.

• Insert the push bar into the rear steering tube in the back of the tricycle frame. Make sure to line up the hole in the push bar with the hole

in the tube.

• Insert the knob screw through the hole and secure with a knob nut. Tighten the nut securely. See Figure 16.

!WARNING

The baby surround system should be used for children who are not yet capable of sitting in the seat

without support or who are not capable of pedaling the product by themselves.

7 Attaching/Detaching the Baby Surround (OPTIONAL)

NOTE: If you are not using and have not attached the baby surround connector then skip these steps in this section.

• Insert one of the baby surround arms into one of the sides of the baby surround base.

• Fasten securely in place with a washer head screw. See Figure 17.

• Repeat these steps for the other surround arm.

• Place the baby surround base on the top of the seat back and push down until a click is heard. See Figure 18.

• Pull up on the base to ensure that it is secure.

• Identify the small black secondary arm lock on each arm and note their locked position. Remove each of them by pulling out on the bottom

tabs, and then pulling up on the lock. See Figure 19.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Joovy Tricycoo 0017X in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 0.46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Joovy Tricycoo 0017X Manual

Product: