780390

Joovy Scooter X2 807X Manual

4
Zoom out
Zoom in
Previous page
1/16
Next page
EN FR ES
6 Front Wheel Locks
• The front wheels can be either in swivel mode or locked mode.
• To put each front wheel set into its locked mode, push down on the locking tab located at the top of the wheel housing and between the
wheels. Be sure to push the locking tab all the way down until an audible click is heard. See Figure 6.1.
NOTE: You may need to rotate the front wheel so the swivel lock tab is facing the rear of the stroller.
• To unlock each wheel and put it into swivel mode, pull up on the locking tab to disengage the lock.
7 Seatback Positioning
Each seatback can be adjusted to any position from fully upright to reclining. These seats should only be used for children who are at least
3 months old. For children between 3 and 6 months, use the most reclined position. For children 6 months and older, use the more upright
positions.
• Engage the rear wheel brakes.
• Locate the recline mechanism on the backside of the seat.
• To recline a seat, grasp the buttons on the top and bottom of the recline mechanism and gently pull towards the rear of the stroller until the
seat is in the desired position. See Figure 7.1.
• To adjust a seatback to a more upright position, pull the straps at the end of the recline mechanism rearward while pushing the
mechanism forward until the seatback is in the desired position. See Figure 7.2.
NOTE: To get a seatback into its most upright position you may need to push the seatback toward the front of the stroller before
pulling the straps.
!
WARNING
ALWAYS ensure that the seat back is secured into position before placing a child in the seat.
Push down on the seatback to be sure it is secure.
NEVER adjust the seatback when the child is in the seat.
Use the more upright seatback positions ONLY for children who are at least 6 months old.
8 Adjusting the Leg Supports
The leg support can be adjusted to two positions horizontal or all the way down.
• To place the leg support into the down position, locate the trigger mechanism underneath BOTH sides of the leg support on the bottom.
Squeeze BOTH triggers and rotate the leg support down. See Figure 8.1.
NOTE: The leg support does not “lock” into the down position, but will remain there by gravity only.
• Therearefabricapsthatcoverthetriggers.Ifnecessary,pulleachapoverthetriggerandattachtheVelcro®tosecureit.
• To place the leg support into the horizontal position, pull up on both sides of the leg support until it is locked into position. See Figure 8.2.
• Push down on both sides of the leg support to ensure it is secure.
!
WARNING
NEVER allow a child to step onto or sit on the leg support. This may cause the stroller to tip over and injure the child.
9 Installing/Removing the Bumper Bar
• Remove the two safety caps from the frame mount points by pressing the release button and pulling each cap off. See Figure 9.1.
• Locatethebumperbarandorientitwiththemalettingpointedtowardstheseatunitandtheshinyroundrivetheadfacingupward.While
holdingthemalettingsstraight,insertthemalettingsonthebumperbarintothefemalettingslocatedonbothsidesoftheseat.You
will hear both sides of the bumper bar “click” in. See Figure 9.2.
• Pull outward on the bumper bar to ensure it is installed properly and securely.
• Toremovethebumperbar,pressthebuttonslocatedontheundersideofbothmalettingsinwardandpullthebumperbarawayfromthe
seat. See Figure 9.3.
• The bumper bar fabric cover can be removed for cleaning. To remove the fabric cover, simply open the zipper on the inside of the fabric
cover and pull the cover off of the bumper bar.
• Toreplacethecover,removethebumperbarfromthestroller,tthecoveroverthebumperbarwiththezipperfacinginwardandclose
the zipper completely.
• When using the stroller without the bumper bar always replace the safety caps.
!
WARNING
The bumper bar is not a restraint device. ALWAYS secure your child with the restraint system. NEVER lift the stroller
by the bumper bar. Use caution when attaching the bumper bar when there is a child seated in the stroller.
10 Installing, Operating and Removing the Canopy
• Stand behind the stroller with the stroller in the unfolded position.
• Orient the canopy in front of the handlebar with the visor towards the front of the stroller.
• Locatetheplasticslidelocksonthebottomofeachsideofthecanopyandslidethemontotheplasticttingoneachsideofthestroller
just above the rear leg. See Figure 10.1.
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Joovy Scooter X2 807X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Joovy Scooter X2 807X in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 0.69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info