626530
2
Zoom out
Zoom in
Previous page
1/2
Next page
enjoy motors ®
JE40R4 is a product from Jolly Motor España, s.l. www.jollyespana.com · www.enjoymotors.es
2
JE40R4_eng_ver.03022012
4-1
MANUAL LIMIT SWITCH ADJUSTMENT - UP LIMIT SWITCH (roller shutter opened) through the
transmitter
1
1
Move the roller shutter
upward and STOP the
motor when it reaches the
UPPER wished limit point
Press ONE time P3
button (located on the
back of the emitter)
Immediately, press ONE
time UP button
Then the motor will make
a single tilt movement as
ConrmationthatUPPER
limit switch has been set up
4-2
MANUAL LIMIT SWITCH ADJUSTMENT - DOWN LIMIT SWITCH or roller shutter closed through
the transmitter
1
1
Move the roller shutter
upward and STOP the
motor when it reaches the
LOWER wished limit point
Press ONE time P3
button (located on the
back of the emitter)
Immediately, press ONE
time DOWN button
Then the motor will make
a single tilt movement as
ConrmationthatLOWER
limit switch has been set up
5-1 LIMIT SWITCH DELETING - DOWN LIMIT SWITCH or roller shutter closed
3
1
1
Press THREE times the
P3 button (located on
the back of the emitter)
Immediately press ONE
time DOWN button
Then the motor will
make a single tilt move-
mentasConrmation
that LOWER limit switch
has been deleted
Press ONE time STOP
button to exit the program-
ming mode
5-2 LIMIT SWITCH DELETING - UP LIMIT SWITCH
3
1
1
Press THREE times the
P3 button (located on
the back of the emitter)
Immediately press ONE
time UP button
Motor will make a single
tiltmovementasConr-
mation that UPPER limit
switch has been deleted
Press ONE time STOP
button to exit the program-
ming mode
6 THIRD LIMIT SWITCH ADJUSTMENT it can be any point between up and down limit switches
4
Move the roller shutter downward or upward and
when it reaches the desire position, stop the motor
(it can be any point between up and down limit
switches)
Press FOUR times
STOP button
Motor will make a single tilt
movementasConrmation
that THIRD limit switch has
been set up
Note: After programmed the midpoint, the shutter will goes to this point, pressing and keep pressing the Stop
button till the motor start to move (± 4 sec) If is needed change the middles position, you can make it as the
above instructions without cancel the precedent position (just only make a new one)
71 ENABLEMENT NEW EMITTERS through the original one
8 1
1
On the Original emitter:
Press EIGHT times the
P3 button (located on the
back of the emitter)
On the New emitter:
Immediately, press ONE
time the P3 button (lo-
cated on the back of the
emitter)
Then the motor will make
a single tilt movement as
Conrmationthatanew
emitter has been learned
Note: It is recommended
press ONE time stop
button, to exit the
programming mode
7-2 ENABLEMENT NEW EMITTERS through a power switch OFF/ON
switch
ON
1
Switch power Off, in the
motor which we want get
a new emitter.
After 5 seconds, switch
power on (connecting the
motor as the wires con-
nect way above)
Then the motor will make
a single tilt movement,
indicating that it is ready
to learning an emitter
On the New emitter:
Within 10 seconds, press
ONE time the P3 button
(located on the back of
the emitter)
Then the motor will make
a single tilt movement as
Conrmationthatanew
emitter has been learned
NOTE: to learn a new emitter, you must connect only one motor on the power or at least be sure that the
switch OFF / ON is being done on the motor which you want to learn the emitter. If more than one motor
are connected to the same power line and the switch OFF / ON is done on them, all of these motors will
learn the emitter over is pressed the P3
7-3 ENABLEMENT NEW EMITTERS through the button placed on the motor head
press and
release
1
1
With the motor put
in power, press (ad
release) ONE time on
the button placed on the
motor head
Then the motor will make
a single tilt movement,
indicating that it is ready
to learning an emitter
New emitter:
Immediately press
ONE time P3 button
(located on the back of
the emitter)
Then the motor will make
a single tilt movement as
Conrmationthatithas
learned a new emitter
8 DELETING A TRANSMITTER
6
1
Press SIX times P3 button (lo-
cated on the back of the emitter)
Immediately press ONE time
UP button
Then the motor will make a single
tiltmovementasConrmationthat
the emitter has been cancelled
9-1 ENABLEMENT POINT TO POINT FUNCTION for Venetian blind or orientable roller shutters
2
1
1
Press TWO times P3
button (located on the
back of the emitter)
Immediately press ONE
time UP button
Then the motor will make
a single tilt movement as
Conrmationthatpointto
point function (TILT) has
been Activated
Press ONE time STOP
button to exit the program-
ming mode
NOTE: when this function is enablement, the motor works step by step in order to get the reach slats orien-
tation. If you want open or close the Venetian blind or shutter, press and hold (up or down button) until the
roller shutter begins to move
TILT
TILT
1 1
Press & release
AUTO
AUTO
1 1
Press & hold 3’’
Note: Once we have gone up or down the blinds automatically, to return to the TILT, we must press a Stop
button once. This is enabled again instantly.
9-2 DISABLEMENT POINT TO POINT FUNCTION working in automatic mode
2
1
1
Press TWO times P3
button (located on the
back of the emitter)
Immediately press ONE
time DOWN button
Motor will make a tilt move-
mentasConrmationthat
point to point function (TILT)
has been Disabled
Press ONE time STOP
button to exit the pro-
gramming mode
AUTO
AUTO
1 1
Press & release
2


Need help? Post your question in this forum.

Forumrules
1

Forum

jolly-motor-je40r4

Reset search

  • I need to maintain my JE40R4 motorised roller blind as it is making a noise during operation. Can you tell me how to gain access to the oiling points as the cover does not seem to flap open. The blind is about 3 metres long.
    Many thanks
    Adam Submitted on 21-1-2021 at 15:25

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jolly Motor JE40R4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jolly Motor JE40R4 in the language / languages: English as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info