Manual Joie iBase - Juva (page 7 of 68) (English, German, Dutch, French, Italian, Portuguese, Swedish, Turkish, Spanish)

768451

Zoom out

Zoom in

1/68

11 12

Concerns on Installation

! DO NOT install this infant child restraint on vehicle seats with Lap

Belts.(Fig. 1)

! This infant child restraint is suitable for vehicle seats with a 3-point

Retractor Safety Belt (with or without base) ONLY (Fig. 2), and

ISOFIX anchor points WITH the Base. (Fig. 3)

! DO NOT install this infant child restraint on vehicle seats that face

sideways or rearward with respect to the moving direction of the

vehicle. (Fig. 4.1)

! DO NOT place rear-facing infant child restraint on frontal seat with

air bag (Fig. 4.2), death or serious injury may occur. Please

reference vehicle owner’s manual for more information.

! It is recommended to install this infant child restraint on the rear

vehicle seat. (Fig. 4.3)

! DO NOT install this infant child restraint on vehicle seats movable

during installation.

! To know more detailed installation information for seat with base,

please refer to the section 'Vehicle Fitting Information'.

Installing with Base

a. Installation with 3-point-belt

1. Unfold the load leg from storage compartment. (Fig. 5)

2. After placing the base on the vehicle seat, extend the load leg to

floor (Fig. 6), the load leg indicator shows green means it is installed

correctly, red means it is installed incorrectly. (Fig. 6.3)

! The load leg has 24 positions. When the load leg indicator

shows red this means the load leg is in the wrong position.

! Make sure the load leg is secure by pressing down on the front

of the base.

! Squeeze the load leg releasing button, then shorten the load leg

upwards.

3. Open the lock-off and route the vehicle safety belt through the

belt path (Fig. 7.1), and lock it into the buckle. (Fig. 7.2)

4. Tighten the vehicle safety belt as much as possible while pushing

down on the base, and check it is not loose or twisted, then close

the lock-off. (Fig. 7.3)

! The infant child restraint can not be used if the vehicle safety

belt with female buckle is too long to tie the base. (Fig. 7.4)

! Check that the safety belt does not move by pulling and pushing

hard on base. If belt loosens or lengthens, repeat procedure.

The installed base is shown as Fig. 8

! Please ensure that there is no gap between the vehicle seat and the

bottom of the base.

! The safety belt must go under the lock-off, not over the lock-off.

(Fig. 8.1)

! The safety belt must be locked into the buckle. (Fig. 8.2)

! The load leg must be installed correctly with green indicator.

(Fig. 8.3)

5. Push the infant carrier module down into the base (Fig. 9), if the

infant child restraint is secure, the infant child restraint indicator

shows green. If the infant child restraint is not secure, the indicator

shows red. (Fig. 10)

! Pull up on the infant carrier module to be sure it is securely

latched into the base.

6. To release the infant carrier module, pull the infant carrier module up

while squeezing the infant carrier module release button. (Fig. 11)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Joie iBase - Juva in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Turkish, Spanish as an attachment in your email.

The manual is 2,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Joie iBase - Juva Manual

Product: