37750

Johnson Control T600MEP-3 Manual

5
Zoom out
Zoom in
Previous page
1/17
Next page
T600MEP-3 Multi-stage Economizer Thermostat Installation Instructions 5
• Outdoor Temperature – An outdoor air temperature
sensor must be connected.
• Applicable Alarms – The backlight lights up as an
alarm condition is displayed.
Note: Press the YES/SCROLL key to temporarily stop
this menu from scrolling.
The Main User Menu is used to access and change
the basic operating parameters of the thermostat.
Access this menu by pressing the MENU key during
normal thermostat operation.
The Installer Configuration Menu is used to set up
the thermostat for application-specific operation. To
access this menu, press and hold the MENU key for
approximately 8 seconds.
Configuring the T600MEP-3 Thermostat
The T600MEP-3 thermostat comes from the factory
with default settings for all configurable parameters.
The default settings are shown in Table 2. To
reconfigure the parameters via the thermostat, follow
the steps in this section.
To access the Installer Configuration Menu, press and
hold the MENU key for approximately 8 seconds.
Note: If the Password parameter has been
configured, Password 0 appears on the thermostat
display indicating that the configured password must
be entered in order to proceed. Use the UP/DOWN
arrow keys to indicate the configured password, then
press the YES key to proceed through the Installer
Configuration Menu parameters.
Once the Installer Configuration Menu begins, press
the NO key to scroll through the parameters listed in
Table 2. When the desired parameter is displayed, use
the YES key to choose the desired selection option.
Press the YES key and then the NO key to continue
scrolling through the parameters.
To exit the Installer Configuration Menu any time, press
the MENU key, and at the exit prompt, press the YES
key. To pass over a parameter without changing it,
press the NO key.
When the thermostat is in the Installer Configuration
Menu and left unattended for approximately 8 seconds,
the thermostat reverts to the Status Display Menu.
Configuring Inputs DI1 and DI2
When DI1 and DI2 are configured for an alarm
condition, an alarm condition is displayed locally when
the input is closed. An alarm message is included on
the scrolling Status Display Menu and when the
message is displayed, the backlight momentarily
lights up.
Each input can be configured to the Selection Options
included in Table 2.
Table 2: Installer Configuration Menu (Part 1 of 5)
Parameter
Appearing
on Display
Description and Default Selection Options
DI1
1
Configuration of Digital Input 1.
Default: None
(None): No function is associated with an input.
(Service): A Service alarm is displayed on the thermostat when the
input is energized. This input can be tied into the air conditioning unit
control card, which provides an alarm should there be a malfunction.
(Filter): A Filter alarm is displayed. This alarm can be connected to a
differential pressure switch that monitors a filter.
(RemOVR): Temporary occupancy request via a remote input. This
override function is controlled by a manual remote occupancy
override. When enabled, this condition disables the override
capability of the thermostat.
(RemNSB): Remote Night Setback (NSB) via a time clock input, an
occupancy sensor, or from a voltage-free contact.
Contact open = Occupied; contact closed = Unoccupied.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Johnson Control T600MEP-3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Johnson Control T600MEP-3 in the language / languages: English as an attachment in your email.

The manual is 0,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info