545551
5
Zoom out
Zoom in
Previous page
1/9
Next page
WWW.JOBO.COM
5
6. Mounting Your Camera
Drill Series versatile CamLOCK Mount System allows you to attach the DRILL B camera to
any type of helmet (bike, motorcycle, ski, skydive etc.), pole, board (surf, skate, ski etc) and
handlebar (bike and motorcycle).
6.1 Secure Strap
1. Loop one end of the secure strap through the strap hole of the camera. You may use a
pin to help thread it thru the hole.
2. Attach other half to the mount or other secure place
3. Clip both ends together when camera is mounted.
6.2 Fix The CamLocker
1. Fit the screw of the CamLocker to the tripod socket of the camera.
2. Screw the CamLocker until it is tightened on the camera.
6.3 Installing your Helmet Mount with Strap
1. Choose the suitable strap to mount on different
types of helmets. . For example, use the short
mount strap for bike helmets and the medium
mount strap for motorcycle helmets.
2. Remove the 2 strap clips from the strap.
3There are three vents at each side of the Helmet
mount. Loop the strap through the inner vent (closest to the center) from the bottom. (Step
1)
.4.Loop the strap through the strap clip from the top.
(Step 2)
5..Loop the strap through middle vent from the top. (Step
3)
6.Loop the strap through the outer vent from the bottom
(Step 4)
7.Tighten the strap and repeat Step 1 4 on the other side.
6.4 Mounting on your Bike Helmet
1. Choose the Helmet Mount with the suitable length of strap.
2. Adhere the single sided adhesive mount to the base of the helmet mount. Use the
double sided adhesive mount to permanently secure the mount to the helmet.
3. Loosen and detach the ball joint nut from the helmet mount.
4. Install the CamLocker Socket Ball Joint to the helmet mount and tighten the nut.
5. Loop the strap of the helmet mount through the vents of the bike helmet and back
through the strap clip.
6. Fasten the strap.
7. Repeat on the opposite end of the strap until the helmet mount is firmly attached to the
helmet.
8. Attach the CamLocker and camera into the CamLocker socket. Ensure that the
CamLocker nut is tightened securely.
9. The ball joint system allows you to change the angle of the camera. Simply loosen the
nut, adjust the camera angle and re-tighten the nut.
6.5 Mounting on your Motorcycle Helmet
1. Adhere the helmet mount to the helmet by applying a double-sided 3M adhesive
mount. By utilizing a combination of the helmet mount and fitting piece, it will provide
additional security to the mount system.
2. Select the Helmet Mount with suitable length of strap.
3. Loosen and detach the ball joint nut from the helmet mount.
4. Install the CamLocker Socket Ball Joint (L) to the helmet mount and tighten the nut.
5. Adhere the double sided adhesive mount to the base of the helmet mount and fitting
piece.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jobo JIB aero at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jobo JIB aero in the language / languages: English as an attachment in your email.

The manual is 0,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info