701357

JL Audio XR525-CSi Manual

2
Zoom out
Zoom in
Previous page
1/8
Next page
XR525-CSi SPECIFICATIONS:
Woofers: Mineral-filled polypropylene cone body,
1-inch (25mm) voice coil, low-profile/symmetrical-
roll spider, butyl rubber surround.
Tweeters: 1-inch (25 mm) aluminum dome
tweeter with rubber surround, neodymium
magnet, ferrofluid cooled and damped.
Adjustable tweeter angle.
Crossover Networks: 2-way network with 1st
order low-pass and 2nd order high-pass circuit.
Premium polypropylene film capacitors and air-core
inductors. 5-position adjustable tweeter output
level. 3-position midrange presence control.
Polyswitch tweeter protection.
Continuous Power Handling:
60 Watts (RMS Method)
Frequency Response: 53 Hz - 25 KHz (± 3 dB)
Efficiency @ 1W/1m: 89.5 dB
Nominal Impedance: 4 ohms
Included Components and Parts:
• Two XR525-CW 5.25-inch (130 mm) woofers
• Two XR100-CT 1-inch (25 mm) tweeters
• Two XR525-CSpxo 2-Way Crossover networks
• Two Flush-Mount tweeter fixtures with metal
spring clips and optional trim rings.
• Two Surface-Mount tweeter fixtures.
• Two Metal Woofer Grilles and Grille Trays
• Butyl adhesive putty for woofer grilles
• Twelve #8 x 1
1
/4-inch (30 mm) sheet metal screws
• Four #6 x
5
/8-inch (16 mm) sheet metal screws
• Two 1-inch (25 mm) machine screws
• Eight Mounting Clips
• Two 6.4 mm female crimpable connectors
• Two 4.7 mm female crimpable connectors
• Four 2.8 mm male crimpable connectors
• Twelve crimpable spade connectors
• Four black nylon wire ties
GETTING STARTED:
• Turn off the audio system. It is also advisable
to disconnect the negative (-) terminal of your
vehicle’s battery whenever performing
installation work.
• Before cutting, drilling or inserting any screw,
check clearances on both sides of the planned
mounting surface. Also check for any potential
obstacles, such as window tracks and motors,
wiring harnesses, etc. Check both sides of the
vehicle, many vehicles are not symmetrical!
• Always wear protective eyewear.
WARNING!
It is absolutely vital that your component
system is connected as shown in the diagrams on
page 3. Failure to connect the system as shown
will result in damage to your speakers which is
NOT covered under warranty. Do not substitute
different crossover networks into your
XR525-CSi System. Only use crossover networks
clearly marked “XR525-CSpxo”.
STANDARD OR BI-WIRE (BI-AMP)
INPUT SELECTION:
The input to the crossover networks can be set
up two ways:
Standard: Your crossovers are pre-set in this
position at the factory.This position is selected by
placing the jumpers in the lower position as shown
at the top of page 3. Use this setting to drive the
crossovers with a single amplifier channel or pair of
wires. In this mode, you will only use the input
connections marked “Main Input” on the crossover
cover (“INL+” and “INL–” on the crossover circuit
board.) Follow the white markings labeled
“Standard” on the crossover cover.
2 JL AUDIO XR525-CSi
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio XR525-CSi at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio XR525-CSi in the language / languages: English as an attachment in your email.

The manual is 0,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info