700455
10
Zoom out
Zoom in
Previous page
1/24
Next page
10 | JL Audio - XD700/5v2 Owners Manual
“Remote Level Mode” Switch: This switch
allows you to assign the operation of the HD-RLC
to the entire amplifier or only the subwoofer
channel. In the “Al l position, the HD-RLC knob
will affect all channels equally. In the “Sub Ch.”
position, only the level of the subwoofer channel
will be affected by the HD-RLC knob.
SPEAKER OUTPUTS
The XD700/5v2’s speaker outputs are designed
to accept 16 AWG - 8 AWG wire. To connect the
speaker wires to the amplifier, first back out the
set screws on the top of the terminal block, using
the supplied 2.5 mm hex wrench. Strip 1/2 inch
(12 mm) of insulation from the end of each wire
and insert the bare wire into the terminal block,
seating it firmly so that no bare wire is exposed.
While holding the wire in place, tighten the set
screw firmly, taking care not to strip the head of
the screw.
Each pair of the XD700/5v2’s main channels are
designed to deliver power into speaker loads equal
to or greater than 2 ohms when using a “stereo”
configuration and speaker loads equal to or greater
than 4 ohms when using a “bridged” configuration.
The subwoofer channel is designed to deliver power
into subwoofer loads equal to or greater than 2 ohms.
Speaker loads below 2 ohms nominal per
channel (or 4 ohms bridged) are not
recommended and may cause the amplifier to
initiate a protection mode which reduces
power output.
BRIDGING CONSIDERATIONS
Bridging is the practice of combining the
output of two amplifier channels to drive a single
load. When bridged, each channel produces
signals of equal magnitude, but opposite polarity.
The combined output of the two channels
provides twice the output voltage available from a
single channel. The XD700/5v2 has been designed
for bridging of its main channel pairs without the
need for input inversion adaptors.
To bridge a pair of main channels, use the
“Left +” and “Right –” speaker connectors only
(the “Left –” and “Right +” remain unused). Each
bridged channel pair will deliver optimum power
into a 4 ohm load.
When a pair of the XD700/5v2’s main channels
are bridged, they will deliver 200W x 1 into a
4 ohm load or 150W x 1 into an 8 ohm load.
Operating a pair of bridged channels into a
load lower than 4 ohms is not recommended.
A bridged pair of channels requires that both
channels in the pair receive input. You must
connect the mono or stereo source signal to
both the left and right inputs of the bridged
channel pair. Connection of only one input will
result in reduced power output, increased
distortion and can cause the amplifier to
overheat. Do not do this!
When a pair of the XD700/5v2’s main channels
are operating in bridged mode, the output will be
in mono (only one channel). This mono channel
can contain only right channel information, only
left channel information, or the sum of the signals
from right and left input channels. In order to
achieve one of these options, configure the inputs
to that pair of channels in one of these two ways:
1) Left Channel Only or Right Channel Only
Information: If you wish to send a left-only or
right-only signal to a pair of the XD700/5v2’s
channels you must use a “Y-Adaptor” to split
the single channel signal into both left and
right RCA inputs of the bridged channel pair.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio xd700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio xd700 in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info