700459
11
Zoom out
Zoom in
Previous page
1/20
Next page
11
pair of the XD400/4v2’s channels to drive left
channel speakers only and the other pair of the
XD400/4v2’s channels to drive right channel
speakers only.
2) Left + Right Channel Information: When
bridged and fed by a stereo source signal, a
bridged pair of the XD400/4v2’s channels
will automatically combine the left and
right input signals into a summed mono
(left + right) input signal. This option is
useful when using a pair of the XD400/4v2’s
channels to drive a subwoofer system
or a summed mono center channel.
STATUS LED / PROTECTION CIRCUITRY
There is a single multi-color LED on the top
surface of the amplifier to indicate the amplifier’s
operating status.
Input Mode
All
|
3&4
1&2
|
Sum
Preouts From Remote Level Mode
4 Channel Amplifier
Input Voltage
Turn-On Mode
1) Flashing Green: The amplifier is powering up,
audio output is muted.
2) Constant Green: The amplifier is on and
functioning normally, audio output is active.
3) Constant Red: lights to indicate that the
amplifier has exceeded its safe operating
temperature, putting the amplifier into a
self-protection mode, which reduces the
peak power output of the amplifier. When
its temperature returns to a safe level, the red
light will return to green and the amplifier will
return to full-power operating mode.
4) Constant Amber (Yellow): Indicates that an
over-current condition has occurred and is
accompanied by a muting of the amplifier’s
output. Because the muting behavior may be
very short in duration, it may manifest itself
as an audible, repetitive ticking or thumping
noise in the output. Over-current conditions
can be caused by a speaker impedance lower
than the optimum load impedance range for
the amplifier or a short-circuit in the speaker
wiring. The latter can result from a short circuit
between the positive and negative speaker
wires or between either speaker wire and the
vehicle chassis. The “Status LED” will remain
amber for a few seconds, even if the over-
current condition is of a very short duration.
5) LED off / Amplifier Shuts Off Unexpectedly
The only condition that will shut down an
undamaged XD400/4v2 completely is if battery
voltage or remote turn-on voltage drops below
10 volts. The “Status LED” will turn off when
this occurs. The amplifier will turn back on
when voltage climbs back above 11 volts. If
this is happening in your system, have your
charging system and power wiring inspected.
For more information on troubleshooting this
amplifier, refer to Appendix D (pages 16, 17).
SERVICING YOUR JL AUDIO AMPLIFIER
If your amplifier fails or malfunctions, please
return it to your authorized JL Audio dealer so
that it may be sent in to JL Audio for service.
There are no user serviceable parts or fuses inside
the amplifier. The unique nature of the circuitry
in the JL Audio amplifiers requires specifically
trained service personnel. Do not attempt
to service the amplifier yourself or through
unauthorized repair facilities. This will not only
void the warranty, but may result in the creation of
more problems within the amplifier.
If you have any questions about the installation or
setup of the amplifier not covered in this manual,
please contact your dealer or technical support.
JL Audio Technical Support:
(954) 443-1100
9:00 AM – 5:30 PM (Eastern Time Zone)
Monday - Friday
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio XD400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio XD400 in the language / languages: English as an attachment in your email.

The manual is 1,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info