700450
6
Zoom out
Zoom in
Previous page
1/41
Next page
10 | JL Audio - XD1200/1v2 Owners Manual
11
ENGLISH
STATUS LED / PROTECTION CIRCUITRY
There is a single multi-color LED on the top
surface of the amplifier to indicate the amplifier’s
operating status.
1) Flashing Green: amplifier is powering up,
audio output is muted.
2) Constant Green: amplifier is on and
functioning normally, audio output is active.
3) Constant Red: lights to indicate that the
amplifier has exceeded its safe operating
temperature, putting the amplifier into a
self-protection mode, which reduces the
peak power output of the amplifier without
muting the audio. When its temperature returns
to a safe level, the red light will return to green
and the amplifier will return to full power
operating mode.
4) Constant Amber (Yellow): Indicates
that an over-current condition has occurred and
is accompanied by a muting of the amplifiers
output. Because the muting behavior may be
very short in duration, it may manifest itself as
an audible, repetitive ticking or thumping noise
in the output. Over-current conditions can be
caused by a speaker impedance lower than the
optimum load impedance range for the amplifier
or a short-circuit in the speaker wiring. The
latter can result from a short circuit between the
positive and negative speaker wires or between
either speaker wire and the vehicle chassis.
The “Status LED” will remain amber for a few
seconds, even if the over-current condition is of a
very short duration.
5) LED off / Amplifier Shuts Off Unexpectedly
The only condition that will shut down
an undamaged XD1000/1v2 completely is if
battery voltage or remote turn-on voltage drops
below 10 volts. The Status LED” will turn off.
when this occurs. The amplifier will turn back
on when voltage climbs back above 11 volts.
If this is happening in your system, have your
charging system and power wiring inspected.
For more information on troubleshooting this
amplifier, refer to Appendix D (pages 14, 15).
SERVICING YOUR JL AUDIO AMPLIFIER
If your amplifier fails or malfunctions, please
return it to your authorized JL Audio dealer so
that it may be sent in to JL Audio for service.
There are no user serviceable parts or fuses inside
the amplifier. The unique nature of the circuitry
in the JL Audio amplifiers requires specifically
trained service personnel. Do not attempt
to service the amplifier yourself or through
unauthorized repair facilities. This will not only
void the warranty, but may result in the creation
of more problems within the amplifier.
If you have any questions about the installation or
setup of the amplifier that have not been covered
in this manual, please contact your dealer or
technical support.
JL Audio Technical Support:
(954) 443-1100
9:00 AM – 5:30 PM (Eastern Time Zone)
Monday - Friday
PREOUTS
The XD1000/1v2 incorporates a buffered, pass-
through preamp output section, so that additional
amplifiers can be easily added to the system.
The preamp output delivers the same signal that
is connected to the XD1000/1v2’s inputs.
The preamp output signal is not affected by
the amplifier’s LP Filter (if the input signal is full-
range, the preamp output will be full-range).
If you plan to use the Preouts” to feed
a stereo amplifier, you must connect a
stereo signal to the input of the amplifier.
A mono signal into the amplifier will result
in a mono signal out of the preamp output.
SUBWOOFER OUTPUTS
The XD1000/1v2 is designed to deliver power
into subwoofer loads equal to or greater than 2
ohms of nominal impedance.
The XD1000/1v2’s subwoofer outputs are
designed to accept 16 AWG - 8 AWG wire. To
connect the subwoofer wires to the amplifier,
first back out the set screws on the top of the
terminal block, using the supplied 2.5 mm hex
wrench. Strip 1/2 inch (12 mm) of insulation
from the end of each wire and insert the bare
wire into the terminal block, seating it firmly
so that no bare wire is exposed. While holding
the wire in place, tighten the set screw firmly,
taking care not to strip the head of the screw.
You will notice that there are two “+ positive
connections and two “” negative connections.
This is to facilitate multiple subwoofer wiring.
The two positive and two negative connections
are connected in parallel inside the amplifier.
They are not stereo outputs. Connecting two
subwoofers, each to one set of positive and
negative terminals, will result in a parallel
subwoofer connection. When only connecting
one pair of subwoofer wires, it is not necessary to
use both sets of connections.
Subwoofer loads below 2 ohms nominal are not
recommended and may cause the amplifier
to initiate a protection mode, which reduces
power output.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio XD1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio XD1000 in the language / languages: English as an attachment in your email.

The manual is 4,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info