INSTALLING YOUR VR650-CXi
COAXIALS IN CUSTOM LOCATIONS:
Run speaker wire to the desired mounting
location. If you are running wires into a door, use
existing factory wiring boots whenever possible. If
you are drilling new holes, file their edges and install
rubber grommets into each hole. Then, cover the
wires with a protective PVC sleeve and run them
through the door jamb. Make sure that the wires
will clear door hinges and other structures in the
door. If you are unsure about any part of this
process, please contact your JL AUDIO dealer for
installation help.
Double check the clearance for both speakers
before proceeding.
Use the supplied template on the top of the
product packaging to mark the desired mounting
location. Mark the center and the outline of the
mounting hole as well as the mounting screw
positions. Before drilling or cutting, use a utility knife
to cut any fabric, vinyl or leather from hole
locations. These materials can easily be snagged by
a drill or a saw, causing damage to the panel and
possible bodily injury.
Drill four 1/8” (3 mm) holes for the speaker’s
mounting screws at the positions you have marked.
Also drill a pilot hole in the center of the speaker
mounting hole at this time. Then, using a saber saw,
hole saw or nibbler, make the circular cut out for
the speaker. File any rough edges.
Insert the mounting clips with the flat side
towards the speaker as shown in the diagram.
It is absolutely vital that the speaker frame fits
into the mounting hole cleanly. This must be
checked prior to tightening the screws. Do not
force the frame into a hole that is too small! Do
not tighten the speaker onto an uneven surface! This
will damage your speakers. The speaker should also
fit so that no air leaks around the mounting flange.
Air leaks will cause a severe degradation in sound
quality. Seal any air leaks with silicone, rope caulk or
similar sealant material.
Connect the speaker wires, observing
correct polarity, and install the speaker and grille
tray as shown.
Hand-tighten the screws evenly to avoid
bending the speaker frame!
Break off small pieces of the supplied butyl
adhesive putty and place them on the inside of each
grille tray. This adhesive will hold the grille in place
firmly and prevent rattling. Then insert the metal
grille into the grille tray, squeezing gently around its
edge until it seats firmly into the tray.
JL AUDIO VR650-CXi 3
VR650-CXi SPECIFICATIONS:
Woofers: Injection-molded, mica-filled, polypropylene
cone body, 1-inch (25mm) voice coil, flat-profile/
symmetrical-roll spider, butyl rubber surround.
Tweeters: 1-inch (25 mm) treated textile soft
dome tweeter, neodymium magnet, ferrofluid
cooled and damped.
Continuous Power Handling:
60 Watts (RMS Method)
Frequency Response: 59 Hz - 22 KHz (± 3 dB)
Efficiency @ 1W/1m: 89.5 dB
Nominal Impedance: 4 ohms
Included Components and Parts:
• Two VR650-CXi 6.5-inch (160 mm) Coaxial
loudspeakers
• Two Metal Grilles and Grille Trays
• Butyl adhesive putty for grilles
• Eight #8 x 1 1/4 inch (30 mm)
sheet metal screws
• Eight Mounting Clips
• Two 5.2 mm female crimpable connectors
• Two 2.8 mm female crimpable connectors
GETTING STARTED:
• Turn off the audio system. It is also advisable to
disconnect the negative (-) terminal of your
vehicle’s battery whenever performing
installation work.
• Before cutting, drilling or inserting any screw,
check clearances on both sides of the planned
mounting surface. Also check for any potential
obstacles, such as window tracks and motors,
wiring harnesses, etc. Check both sides of the car,
many cars are not symmetrical!
• Always wear protective eyewear.
INSTALLING YOUR VR650-CXi
COAXIALS IN FACTORY LOCATIONS:
If you will be using the factory speaker wires, it
may be necessary to change the terminations. This
may be accomplished by using an adaptor plug or
simply by cutting the factory connector off and
using the supplied crimp connectors to terminate
the speaker wires.The large connector is for the
positive terminal and the small connector is for the
negative terminal of each VR650-CXi. You may also
choose to run new speaker wires...refer to the
custom installation section for details. Whichever
method you choose, observe correct polarity in
your connections. If you are unsure about any of
these issues, contact your JL AUDIO dealer for
installation assistance.
Your new speakers have been designed
to install, without modifications, into most vehicles
that accept a 6.5-inch (160 mm) speaker. Most
factory 6.5-inch speakers use four mounting screws
which will line up with the mounting holes on your
VR650-CXi speakers. Others use a 3-hole
mounting system which is accommodated by a
separate set of mounting holes on the frames of
your VR650-CXi speakers.
It is absolutely vital that the speaker frame fits
into the mounting hole cleanly. This must be
checked prior to tightening the screws. Do not
force the frame into a hole that is too small!
Do not tighten the speaker onto an uneven surface!
This will damage your speakers. The speaker should
also fit so that no air leaks around the mounting
flange. Air leaks will cause a severe degradation in
sound quality. Seal any air leaks with silicone, rope
caulk or similar sealant material.
Install as shown in the diagram here.
Use the supplied mounting clips unless the
factory holes already feature threaded inserts.
Hand-tighten the screws evenly to avoid bending
the speaker frame!
2 JL AUDIO VR650-CXi
