701368
4
Zoom out
Zoom in
Previous page
1/5
Next page
TWEETER INSTALLATION:
The dome tweeters supplied with your
VR650-CSi system have been designed for
maximum mounting versatility. There are two
primary methods by which the tweeters can be
mounted in your vehicle:
1) Flush Mounted, using the supplied flush-mount
cup and hardware.This application will yield a
custom-installed appearance, but will require at least
3/4-inch (19 mm) of clearance behind the mounting
surface of the tweeter.
2) Surface Mounted, using the supplied surface
mount kit and hardware. In this application, you will
not need to cut holes in your vehicle’s panels for
the tweeters.You will only need to drill a hole for
the wires and for the two mounting screws.This
application is useful when mounting the tweeters to
a panel that has insufficient clearance behind it for
the tweeter’s magnet structure.
Run speaker wires from the tweeter output of
the crossover to the desired tweeter mounting
locations, observing the same precautions as
mentioned in the woofer installation section.
Terminate the wires with the supplied 2.8 mm male
crimpable connectors.
FLUSH MOUNT INSTALLATION:
Swivel/Rotation Mechanism:
Once the tweeter has been mounted into the
flush mount cup as shown above, it can be swiveled
and rotated by hand to best enhance imaging using
the swivel/rotation mechanism built into the flush
mount system. Experiment with different angles
until you arrive at the best solution. The
swivel/rotation feature will not operate with the
surface mount system.
JL AUDIO VR650-CSi 7
1a 1b 1c
1d 1e 2
Assemble the Flush-Mount Cup Mounting Hole Diameter: 1.75 in. (45 mm)
Attach the Tweeter to the Swivel Assembly
Insert the tweeter
and swivel asembly
into the mounted
flush-mount cup,
feeding the wires
through the slots
in the rear of the cup.
Line up the arms of
the swivel assembly
with the slots on the
inside of the flush
mount cup
Tighten
Screw
Vehicle
Panel
Use two thin metal objects as shown to release
the tweeter element from the flush-mount cup.
CROSSOVER NETWORK
INSTALLATION:
The crossover networks supplied with your
VR650-CSi System should be installed in a dry
location of your vehicle. DO NOT INSTALL
THEM INSIDE OF A DOOR! Doors often get
wet on the inside, which can damage your crossover
networks and could potentially damage your entire
sound system.
The crossovers can be screwed into a solid
surface via two holes located under the protective
cover of the case. To access these holes, simply
squeeze the sides of the cover while gently pulling
the cover away from the base. Make sure that your
mounting location will not cause damage to wiring,
fuel lines, brake lines or any other vital component
of your vehicle. Once you have screwed the case in,
snap the protective cover back into place.
If screwing the crossovers networks in is not
possible, you can also run the supplied nylon wire
ties through the mounting holes to attach the
crossovers to a structure in your car. To do so, take
the covers off, attach the wire ties, and then snap
the covers back into place, lining the wire ties up
with the slots on the sides of the protective cover.
Make sure that you do not attach the crossovers to
a moving part or to any part that may interfere with
pedal operation, gear shift operation, steering, or
airbag deployment.
For wiring instructions, refer to the diagram on
pages 2 & 3 of this manual.
6 JL AUDIO VR650-CSi
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio VR650-CSi at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio VR650-CSi in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info