700468
11
Zoom out
Zoom in
Previous page
1/20
Next page
11
If the condition remains, it will return to red
and mute the output again. A continuous
over-current condition is displayed with
alternating red/blue lights. Because the muting
behavior may be very short in duration, it
may manifest itself as an audible, repetitive
ticking or thumping noise in the output.
Over-current conditions can be caused by a
speaker impedance lower than the optimum
load impedance range for the amplifier or a
short-circuit in the speaker wiring. The latter
can result from a short circuit between the
positive and negative speaker wires or between
either speaker wire and the vehicle chassis.
4) LEDs off / Amplifier Shuts Off Unexpectedly
The only condition that will shut down an
undamaged RD400/4 completely is if battery
voltage or remote turn-on voltage drops below
10 volts. The LED light strip will turn off when
this occurs. The amplifier will turn back on
when voltage climbs back above 11 volts. If
this is happening in your system, have your
charging system and power wiring inspected.
For more information on troubleshooting this
amplifier, refer to Appendix C (pages 16, 17).
SYSTEM CONFIGURATIONS
The RD400/4 is a flexible amplifier, well-suited
for a multitude of system configurations. In this
section, the most likely configurations for a system
with a single RD400/4 are explained in detail.
Once you have selected your desired
configuration, you can use the amplifier panel
drawing on pages 18 & 19 to mark the required
switch positions for easy reference.
BIAMPLIFIED SYSTEMS
Bi-amplified systems are defined as systems
in which separate amplifier channels drive low-
frequency (LF) and high-frequency (HF) speakers
and are separately filtered to send appropriate
frequency ranges to each speaker system.
The most common application of
bi-amplification in mobile audio is to drive a
subwoofer system from one or more amplifiers or
channels and component speakers from separate
amplifiers or channels.
The RD400/4 can be configured to drive a
bi-amplified system by itself or with a separate
subwoofer amplifier.
Bi-Amplified System with one RD400/4
In this configuration, channels 3&4 of the
RD400/4 will drive subwoofers (stereo or bridged)
with low-pass filtering. Channels 1&2 will
drive component speakers in stereo with
high-pass filtering.
Input connection options for a bi-amplified system
with one RD400/4 are as follows:
A) No User Adjustability:
Req uired: a basic source unit or processor
with one pair of stereo outputs.
Inp ut Connections: a single pair of stereo source
unit outputs connected to the “CH 1 (Left)
andCH 2 (Right) inputs of the RD400/4
(select2 Ch. on the “Input Mode switch).
Res ult: the relative level of the LF and HF
channels will be determined by the RD400/4s
Input Sensitivity” settings and will not be
user adjustable from the front of the vehicle.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio RD400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio RD400 in the language / languages: English as an attachment in your email.

The manual is 1,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info