700468
7
Zoom out
Zoom in
Previous page
1/20
Next page
7
INPUT SECTION
The RD400/4’s input section allows you to send
signals to the amplifier section through the use of
two or four differential-balanced inputs.
Input connections are via two pairs of
traditional RCA-type jacks.
INPUT SECTION
(
L
)
(
R
)
Left
or
Mono
Right
Only
CH. 1&2 CH. 3&4
CH. 3
(
L
)
CH. 4
(
R
)
CH. 1
(
L
)
CH. 2
(
R
)
BridgedBridged
Speaker OutputsSpeaker Outputs
PREOUTS
+12 VDC Ground Remote
Left
or
Mono
Right
Only
+12 VDC Ground Remote
Input Mode
2 Ch.
|
4 Ch.
Input Voltage
Low
|
High
Rem.
|
Oset
|
Signal
CH. 1
CH. 2
CH. 3
CH. 4
(
L
)
(
R
)
INPUT SECTION
Turn On Mode
PRE-OUTS
CH. 3
(
L
)
CH. 4
(
R
)
CH. 1
(
L
)
CHANNELS 1 & 2
CH. 2
(
R
)
Filter Mode
Filter Freq. (Hz)
Filter Freq. (Hz)
O
|
HP
|
LP
Filter Mode
O
|
HP
|
LP
Input Type Input Sensitivity Input Sensitivity
Stereo
|
Mono
Input Type
Stereo
|
Mono
4 Channel Amplifier
CHANNELS 3 & 4
Clipping
Clipping
If you wish to send four discrete channels into
the RD400/4, simply use all four inputs and set
the Input Mode switch in the 4 Ch. position.
If you wish to use only two channels of input to
deliver signal to all four amplifier channels, set the
“Input Mode” switch to “2 Ch. and use only the
inputs to channels 1 and 2. In this mode, channel
3 will operate with the channel 1 signal and
channel 4 will operate with the channel 2 signal.
INPUT VOLTAGE RANGE
A wide range of signal input voltages can be
accommodated by the RD400/4’s input section
(200mV – 8V). This wide range is split up
into two sub-ranges, accessible via the “Input
Voltage” switch:
“Low: for preamp level signals
“High”: for speaker level signals
This switch affects all channels of the amplifier
equally. The “Low position on the “Input
Voltage” switch selects an input sensitivity range
between 200mV and 2V. This means that the
“Input Sensitivity rotary controls will operate
within that voltage window. If you are using
an aftermarket source unit, with conventional
preamp level outputs, this is the position you
should select.
The “High” position on the “Input Voltage”
switch selects an input sensitivity range between
800mV and 8V. This is useful for certain high-
output preamp level signals as well as speaker
level output from source units and small
amplifiers. To use speaker level sources, splice the
speaker output wires of the source unit or small
amplifier onto a pair of RCA cables or plugs,
or use the JL Audio ECS Speaker Wire to RCA
adaptor (XD-CLRAIC2-SW).
Line output converters are usually not needed
with the RD400/4. If you find that the output
cannot be reduced sufficiently with a direct
speaker level signal applied to the amplifier and
the “Input Voltage” switch in its “High” position,
you may use a line output converter or voltage
divider to reduce the signal level.
INPUT TYPE
Each pair of output channels includes an
“Input Type” switch to configure how the input
signals are fed to the outputs.
Selecting “Stereo” will send signals from both
left and right inputs to their respective outputs.
Selecting “Mono” will send the signal from
the left input (only) to both outputs, without
needing to use Y-adaptors. This is useful when
sending a single mono signal to both outputs
of a channel pair or to a bridged channel pair.
Left
or
Mono
Right
Only
+12 VDC Ground Remote
Input Mode
2 Ch.
|
4 Ch.
Input Voltage
Low
|
High
Rem.
|
Oset
|
Signal
CH. 1
CH. 2
CH. 3
CH. 4
(
L
)
(
R
)
INPUT SECTION
Turn On Mode
PRE-OUTS
CH. 3
(
L
)
CH. 4
(
R
)
CH. 1
(
L
)
CHANNELS 1 & 2
CH. 2
(
R
)
Filter Mode
Filter Freq. (Hz)
Filter Freq. (Hz)
O
|
HP
|
LP
Filter Mode
O
|
HP
|
LP
Input Type Input Sensitivity Input Sensitivity
Stereo
|
Mono
Input Type
Stereo
|
Mono
4 Channel Amplifier
CHANNELS 3 & 4
Clipping
Clipping
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio RD400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio RD400 in the language / languages: English as an attachment in your email.

The manual is 1,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info