700468
3
Zoom out
Zoom in
Previous page
1/20
Next page
3
PLANNING YOUR INSTALLATION
It is important that you take the time to
read this manual and that you plan out your
installation carefully. The following are some
considerations that you must take into account
when planning your installation.
Cooling Efficiency Considerations:
The outer shell of your JL Audio amplifier
is designed to remove heat from the amplifier
circuitry. For optimum cooling performance,
this outer shell should be exposed to the
largest possible volume of air. Enclosing the
amplifier in a small, poorly ventilated chamber
can lead to excessive heat build-up and degraded
performance. If an installation calls for an
enclosure around the amplifier, we recommend
that this enclosure be ventilated with the aid
of a fan. In normal applications, fan-cooling is
not necessary.
Mounting the amplifier upside down is
strongly discouraged. If mounting the amplifier
under a seat, make sure there is at least 1 inch
(2.5 cm) of space above the amplifier’s outer shell
to permit proper cooling.
Safety Considerations:
Your amplifier needs to be installed in a dry,
well-ventilated environment and in a manner
which does not interfere with your vehicle’s safety
equipment (air bags, seat belt systems, ABS brake
systems, etc.). You should also take the time to
securely mount the amplifier so that it does not
come loose in the event of a collision or a sudden
jolt to the vehicle.
Stupid Mistakes to Avoid:
Check before drilling any holes in your vehicle
to make sure that you will not be drilling
through a gas tank, brake line, wiring harness or
other vital vehicle system.
Do not run system wiring outside or underneath
the vehicle. This is an extremely dangerous
practice which can result in severe damage to
your vehicle and person.
Protect all system wires from sharp metal edges
and wear by carefully routing them, tying
them down and using grommets and loom
where appropriate.
Do not mount the amplifier in the engine
compartment, under the vehicle, on the roof or
in any other area that will expose the amplifier
circuitry to the elements.
INPUT SECTION
(
L
)
(
R
)
Left
or
Mono
Right
Only
CH. 1&2 CH. 3&4
CH. 3
(
L
)
CH. 4
(
R
)
CH. 1
(
L
)
CH. 2
(
R
)
BridgedBridged
Speaker OutputsSpeaker Outputs
PREOUTS
+12 VDC Ground Remote
Remote Turn-On
Connector
(pg. 6)
Chassis Ground
Connector
(pg. 5)
Channels 1 & 2
Input Jacks
(pg. 7)
Left & Right
Output Jacks
(pg. 9)
+12 V Power
Connector
(pg. 5)
Channels 3 & 4
Speaker Outputs
(pg. 9)
Channels 1 & 2
Speaker Outputs
(pg. 9)
Channels 3 & 4
Input Jacks
(pg. 7)
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio RD400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio RD400 in the language / languages: English as an attachment in your email.

The manual is 1,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info