700488
19
Zoom out
Zoom in
Previous page
1/24
Next page
19
The Nine-Step Procedure
(follow this procedure for each pair of channels)
1) Disconnect the Speaker Connector Plugs.
2) Turn off all processing on the source unit
(bass/treble, loudness, EQ, etc.). Set fader
control to center position and subwoofer
level control to 3/4 of maximum (if used
to drive the MDH900/5-24V). Disconnect
the HD-RLC Remote Level Control
temporarily (if one is being used).
3) Switch the “Input Voltage” to “Low” and
turn the “Input Sens.” control on both sets of
channels all the way down.
4) Set the source unit volume to 3/4 of full
volume. If the subwoofer channel is being
driven by a source units dedicated subwoofer
output, also adjust the source unit’s subwoofer
level control to 3/4 of maximum output. This
will allow for reasonable gain overlap with
moderate clipping at full volume.
5) Using the chart below, determine the
target voltage for input sensitivity
adjustment according to the nominal
impedance of the speaker system
connected to each set of outputs.
6) Verify that you have disconnected the Speaker
Connector Plugs before proceeding. Play a
track with an appropriate sine wave (within the
frequency range to be amplified by each set of
channels) at 3/4 source unit volume.
7) Connect the AC voltmeter to the “Front
Speaker Outputs” or “Rear Speaker Outputs
connectors of the amplifier. If the channel pair
is operating in stereo, it is only necessary to
measure one channel in the pair. If bridged,
make sure you test the voltage at the correct
connectors (L+ and R–).
8) Increase the “Input Sens.” control until
the target voltage is delivered for that
set of channels. If excessive voltage is
read with the control at minimum (full
counterclockwise), switch the “Input
Voltage” switch to “High” and re-adjust.
9) Once you have adjusted each set of channels to
its maximum unclipped output level, reconnect
the speaker(s). The “Input Sens.” controls can
now be adjusted downward any set of channels
requires attenuation to achieve the desired
system balance.
Nom.
Impedance
FRONT OR REAR
CHANNELS
SUBWOOFER
CHANNEL
Stereo Bridged Mono
8 20.0 V 40.0 V 44.7 V
6 20.0 V 32.0 V 44.7 V
4 20.0 V 24.6 V 44.7 V
3 16.0 V 21.2 V 38.7 V
2 12.3 V
not recommended
31.6 V
1.5 10.6 V
not recommended
27.4 V
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio MHD900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio MHD900 in the language / languages: English as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JL Audio MHD900

JL Audio MHD900 User Manual - English - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info