700488

JL Audio MHD900 Manual

11
Zoom out
Zoom in
Previous page
1/24
Next page
11
channel filter is a low-pass filter (attenuates
high frequencies). For each filter, the user can
select from a shallow (12dB/octave) filter slope
or a more aggressive (24dB/octave) slope.
1) “High-Pass Filter” Controls (Front and Rear
channels) or “Low-Pass Filter” Control (Sub
Channel): These switches allow you to select filter
slopes or defeat the filter(s) completely.
“Off”: Defeats the filter completely. Useful when
using an external crossover, such as one built into
a head unit or signal processor.
“12dB”: Configures the filter to attenuate
frequencies above or below the selected
filter frequency at a rate of 12 dB per octave
(Butterworth alignment).
“24dB”: Configures the filter to attenuate
frequencies above or below the selected filter
frequency at a rate of 24 dB per octave (Linkwitz-
Riley alignment).
Depending on the speaker system and the
vessel, different filter slopes may be required to
produce a smooth transition between the sound
of different speakers in the system.
In high-pass mode, the sharper “24dB” setting
will do a better job of protecting small speakers
with limited power handling. In low-pass
mode, the “24dB” setting can also help by more
aggressively removing lower midrange output
from a subwoofer system.
The shallower “12dB” octave setting
allows for more output overlap between
the speakers being crossed over. In many
cases, this will result in a smoother “blend”
or transition between speaker systems.
Experiment to find the slope or combination
of slopes which best matches the acoustic
requirements of your system.
2) “Filter Freq. (Hz)” Control:
This control selects the frequency at which the
filter begins to attenuate the signal and refers
specifically to the frequency at which output
has been attenuated by -3dB.
The filter frequency markings surrounding this
rotary control are for reference purposes and are
generally accurate to within 1/3 octave or better. If
you would like to select the filter cutoff frequency
with a higher level of precision, consult the charts
in Appendix B (page 18) of this manual.
“80 Hz” is a good starting point for most systems
where a subwoofer is connected to the Subwoofer
Channel and component systems or coaxials to
the four main channels.
INFRASONIC FILTER Subwoofer Ch. Only)
The “Infrasonic Filter” is a 24 dB/octave high-
pass filter, with a fixed cutoff frequency of 30 Hz.
This filter is designed to conserve amplifier power
and protect subwoofer systems, without audibly
degrading the sub-bass output.
With ported enclosures, the use of the
“Infrasonic Filter” is highly recommended to
protect the speaker(s) from excessive excursion
below box tuning.
With sealed enclosures, the use of the filter
is less necessary, but can still help protect the
speaker system from excessive excursion.
The “Infrasonic Filter” can be completely
defeated by selecting the “Off” position on its
switch. This bypasses all signal from flowing
through the circuit.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio MHD900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio MHD900 in the language / languages: English as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JL Audio MHD900

JL Audio MHD900 User Manual - English - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info