700489
14
Zoom out
Zoom in
Previous page
1/24
Next page
14 | JL Audio - MHD750/1 Owners Manual
Speaker loads below 1.5Ω nominal are not
recommended and may cause the amplifier
output to distort excessively.
Speaker Connector Plugs
To connect the speaker wires to the amplifier,
unplug the speaker connector plug from the
amplifier chassis (pull back firmly) and back out
the set screws on the connector plug, using the
supplied 2.5 mm hex wrench. Strip 3/8 inch (10
mm) of insulation from the end of each wire and
insert the bare wire into the receptacle on the
speaker connector plug, seating it firmly so that
no bare wire is exposed. While holding each wire
in place, tighten each set screw firmly, taking care
not to strip the head of the screw.
You will notice that there are two sets of “+” and
“–” connections on the plug. This is to facilitate
multiple speaker wiring to the MHD750/1s mono
output. The two positive and two negative
connections are connected in parallel inside the
amplifier. Connecting two speakers, each to
one set of positive and negative terminals, will
result in a parallel speaker connection. If only
connecting one pair of speaker wires, it is not
necessary to use both sets of connections.
Do not chassis ground any speakers connected
to this or any other JL Audio amplifier. Doing
so will cause the amplifier to go into protection
and mute the output.
“STATUS” LED / PROTECTION CIRCUITRY
There is a single multi-color LED on the
control panel of the amplifier to indicate the
amplifier’s operating status. This LED’s behavior
is as follows:
1) Flashing Green: amplifier is powering up,
audio output is muted.
2) Constant Green: amplifier is on and
functioning normally, audio output is active.
3) Constant Red: lights to indicate that the
amplifier has exceeded its safe operating
temperature, putting the amplifier into a
self-protection mode, which reduces the
peak power output of the amplifier. The red
light will turn green and the amplifier will
return to full-power operating mode when its
temperature returns to a safe level.
3) Constant Amber (yellow): lights to indicate
that the impedance of the speaker load
connected to the amplifier is lower than its
optimum load impedance range. When this
light is on, a protection circuit engages and
reduces the power output of the amplifier.
The amber indicator will also light when a
short-circuit is detected in the speaker wiring
(this can be a short between the positive and
negative speaker wires or between either
speaker wire and the vessel chassis).
4) Alternating Red and Green: lights to indicate
that the amplifier is experiencing a fault
that may require service of the amplifier,
its wiring or the vessel’s charging system.
Audio is muted when this fault occurs. The
most likely cause of this fault is a low supply
voltage condition. If battery voltage drops
below 8.5 volts at any point, the amplifier
(except for the “Status” LED) will shut itself
off to protect itself and the vessel’s charging
system. If the voltage drops below 6 volts,
the “Status” LED will also turn off.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio MHD750 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio MHD750 in the language / languages: English as an attachment in your email.

The manual is 1,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info