700496
6
Zoom out
Zoom in
Previous page
1/20
Next page
6 | JL Audio - M500/3 Owners Manual
TURNON LEAD
The M500/3 uses a conventional +12V remote
turn-on lead, typically controlled by the source
unit's remote turn-on output. The amplifier will
turn on when +12V is present at its Remote
input and turn off when +12V is switched off. If
a source unit does not have a dedicated remote
turn-on output, the amplifiers turn-on lead can
be connected to +12V via a switch that derives
power from an ignition-switched circuit.
The M500/3’s Remote turn-on connector is
designed to accept 18 AWG – 12 AWG wire. To
connect the remote turn-on wire to the amplifier,
first back out the set screw on the top of the
terminal block, using the supplied 2.5mm hex
wrench. Strip 1/2 inch (12mm) of wire and insert
the bare wire into the terminal block, seating it
firmly so that no bare wire is exposed. While
holding the wire in the terminal, tighten the set
screw firmly, taking care not to strip the head of
the screw and making sure that the wire (not the
insulation) is firmly gripped by the wire clamp in
the terminal.
INPUT SECTION
(
L
)
(
R
)
Remote
Level
Control
CH. 1&2 SUB CH. Preouts
+12 VDC Ground Remote
CH. 1
(
L
)
CH. 2
(
R
)
Bridged Mono Subwoofer Output
INPUT SECTION
The M500/3’s input section allows you to send
signals to the amplifier section through the use
of two or four differential-balanced inputs.
Input connections are via one or two pairs of
traditional RCA-type jacks.
INPUT SECTION
(
L
)
(
R
)
Remote
Level
Control
CH. 1&2 SUB CH. Preouts
+12 VDC Ground
Remote
CH. 1
(
L
)
CH. 2
(
R
)
Bridged Mono Subwoofer Output
If you wish to send four discrete channels into
the M500/3, simply use all four inputs and set the
Input Mode switch in the 4 Ch. position. The
amplifier will automatically combine the Sub Ch.
input signals to mono.
You may also choose to apply only two
channels of input to deliver signal to all three
amplifier channels. To do this, set the Input
Mode switch to 2 Ch. and use only the
inputs to channels 1 & 2. The amplifier will
automatically combine the Ch. 1 & 2 input
signals to mono for the Subwoofer Channel.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio M500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio M500 in the language / languages: English as an attachment in your email.

The manual is 1,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info