700498
10
Zoom out
Zoom in
Previous page
1/20
Next page
10 | JL Audio - XD200/2 Owners Manual
SPEAKER OUTPUTS
The M200/2s speaker outputs are designed
to accept 16 AWG - 8 AWG wire. To connect the
speaker wires to the amplifier, first back out the
set screws on the top of the terminal block, using
the supplied 2.5 mm hex wrench. Strip 1/2 inch
(12 mm) of insulation from the end of each wire
and insert the bare wire into the terminal block,
seating it firmly so that no bare wire is exposed.
While holding the wire in place, tighten the set
screw firmly, taking care not to strip the head of
the screw.
The M200/2 is designed to deliver power into
speaker loads equal to or greater than 2 ohms
when using a “stereo” configuration and speaker
loads equal to or greater than 4 ohms when using a
bridged” configuration.
Speaker loads below 2 ohms nominal per
channel (or 4 ohms bridged) are not
recommended and may cause the amplifier
to initiate a protection mode which reduces
power output.
BRIDGING CONSIDERATIONS
Bridging is the practice of combining the
output of two amplifier channels to drive a single
load. When bridged, each channel produces
signals of equal magnitude, but opposite polarity.
The combined output of the two channels
provides twice the output voltage available from a
single channel. The M200/2 has been designed for
bridging of its channel pair without the need for
input inversion adaptors.
To bridge the M200/2, use the Left + and
Right – speaker connectors only (the
Left – and Right + remain unused). When
bridged, the amplifier will deliver optimum
power into a 4 ohm load.
When the M200/2 is bridged, it
will deliver 200W x 1 into a 4 ohm load or
150W x 1 into an 8 ohm load. Operating
a bridged M200/2 into a load lower than 4
ohms is not recommended. Because a bridged
pair of channels requires that both channels
receive input, you need to connect both left
and right inputs to the source unit. Connection
of only one input will result in reduced power
output, increased distortion and can cause
the amplifier to overheat. Do not do this!
When the M200/2 is operating in bridged
mode, the output will be in mono (only one
channel). This mono channel can contain right
channel only information, left channel only
information or the sum of the information from
both the right and left channels. In order to
achieve one of these options, configure the inputs
to that pair of channels in one of these two ways:
1) Left Channel Only or Right Channel Only
Information: If you wish to send a left-only
or right-only signal to the M200/2, use a
“Y-Adaptor” to split the single channel signal
into both left and right RCA inputs. This
option is useful when using one M200/2
to drive left channel speakers only and the
another M200/2 to drive right channel
speakers only.
2) Left + Right Channel Information: When
bridged and fed by a stereo input, the M200/2s
channels will automatically combine the left a
nd right channels into a summed mono (left
+ right) channel. This option is useful when
using a bridged M200/2 to drive a subwoofer
system or a summed mono center channel.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio M200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio M200 in the language / languages: English as an attachment in your email.

The manual is 1,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info