700442
10
Zoom out
Zoom in
Previous page
1/24
Next page
10 | JL Audio - HD750/1 Owners Manual
The output of the amplifier decreases for a
given input voltage when the “Input Range”
switch is placed in the “High” position. The
output increases with the switch in the “Low
position. While this may sound counter-
intuitive, it is correct as described.
“Input Sens.” Control
Located to the left of the Input Voltage
switch is a rotary control labeled Input Sens..
Once the appropriate Input Voltage range has
been selected, this control can be used to match
the source unit’s output voltage to the input stage
of each pair of amplifier channels for maximum
clean output. Rotating the control clockwise will
result in higher sensitivity (louder for a given
input voltage). Rotating the control counter-
clockwise will result in lower sensitivity (quieter
for a given input voltage). To properly set the
amplifier for maximum clean output, please refer
to Appendix C (pages 18, 19) in this manual.
After using this procedure, you can then adjust
the relative level by adjusting the input sensitivity
downward, if it requires attenuation to achieve
the desired system balance.
Do not increase the Input Sens. setting for
any amplifier in the system beyond the maximum
level established during the procedure outlined in
Appendix C (pages 18, 19). Doing so will result in
audible distortion and possible speaker damage.
CROSSOVER CONTROLS
Crossovers are groups of electronic filters
designed to control the frequency ranges
that each speaker in a system will be tasked
with reproducing. Proper crossover setup is
critical to sound quality and reliability.
The HD750/1 has one filter, which can be
configured as a high-pass filter (attenuates low
frequencies) or as a low-pass filter (attenuates
high frequencies). Additionally, the user can
select from a shallow (12dB/octave) filter slope
or a more aggressive (24dB/octave) slope.
1) Filter Mode Control: this switch allows you
to defeat or configure the filter into one of two
filter types:
Off: Defeats the filter completely, allowing
the full range of frequencies present at the
inputs to feed the amplifier. This is useful
for systems utilizing outboard crossovers or
requiring full-range reproduction.
HP (High-Pass): Configures the filter
to attenuate frequencies below the selected
filter frequency. Useful for connection of
component speakers in a bi-amplified system.
LP (Low-Pass): Attenuates frequencies
above the selected filter frequency.
Useful for connection of subwoofer(s)
in a bi-amplified system.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio HD750 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio HD750 in the language / languages: English as an attachment in your email.

The manual is 1,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info