700442
6
Zoom out
Zoom in
Previous page
1/24
Next page
6 | JL Audio - HD750/1 Owners Manual
POWER AND TURNON CONNECTIONS
Before installing the amplifier, disconnect the
negative (ground) wire from the vehicles battery.
This will prevent accidental damage to the system,
the vehicle and your body during installation.
Remote
Level
Control
Inputs
L
R
L
R
+12 VDC Ground Remote
Preouts
+12 VDC Ground Remote
+12V Battery Connection
You will need to connect a power wire to
the vehicle’s positive battery terminal, using an
appropriate power ring or specialized battery
terminal connector, such as the JL Audio
XB-BTU. This connection must be tight and
corrosion-free to ensure proper connectivity. This
wire MUST be fused appropriately for safety. Any
power wires run through metal barriers (such as
firewalls), must be protected with a high quality
insulating grommet to prevent damage to the
insulation of the wire. Failure to do so may result
in a dangerous short circuit.
Power Wire Requirements
The HD750/1s +12 VDC and Ground
connections are designed to accept 4 AWG power
wire. 4 AWG pure copper wire is recommended
for any power wire run longer than 72 inches (180
cm). For runs shorter than 72 inches, 8 AWG pure
copper power wire is acceptable.
If you are installing the HD750/1 with other
amplifiers and wish to use a single main power
wire, use 2 AWG or 1/0 AWG pure copper wire
as a main power wire. This 2 AWG or 1/0 AWG
power wire should terminate into a distribution
block mounted as close to the amplifiers as
possible and should connect to the HD750/1 with
4 AWG or 8 AWG pure copper power wire.
Please note that lower AWG numbers mean
bigger wire and vice-versa (1/0 AWG is the largest,
2 AWG is smaller, then 4 AWG, then 8 AWG, etc.).
We do not recommend the use of “copper-clad
aluminum wire” or “CCA” wire because this
wire is significantly less conductive than pure
copper wire. Only use pure copper power wire,
such as JL Audio Premium Power Wire.
Tinned copper wire (silver color) is acceptable
as the tin-plating is only a very minor
component of the wire.
Fuse Requirements
The installation of a fuse on the main power
wire, within 18 wire inches (45 cm) of the positive
battery terminal is vital to protect the wire and
the vehicle from fire in the event of a collision
or short-circuit. The fuse value at each power
wire should be just high enough for all of the
equipment being run from that power wire. Do
not use a fuse with a value that far exceeds the
total fuse rating of the electronics connected to
the wire.
If only the HD750/1 is being run from
that power wire, we recommend a 60A fuse
be used. AGU (big glass fuse). AFS (small
blade fuse) or MaxiFuse™ (big plastic-
body fuse) types are recommended.
If other amplifiers are also being powered from
a main power wire and exceed 80 amps in total
fuse rating, we recommend the use of an ANL
(large-blade) fuse and holder. Each amplifier
must be fused independently at the outputs of
the power distribution block. Use JL Audio part
XC-FOA-2PAK and appropriate MaxiFuse™
type fuses with JL Audio distribution blocks.
Please consult with your JL Audio
dealer to make sure that the wire, fuse
holder and fuse ratings are appropriate
for your system’s needs. The safety of
your installation depends on appropriate
power connections and fuse protection.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio HD750 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio HD750 in the language / languages: English as an attachment in your email.

The manual is 1,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info