701251
5
Zoom out
Zoom in
Previous page
1/12
Next page
5
TWEETER INSTALLATION
C1 tweeters have been designed for surface
or flush-mounting. Before choosing a method,
carefully inspect the desired mounting location
to determine which method will work best.
Surface-Mount: uses the supplied surface-mount
fixture and requires the drilling of three holes (one
for the wires and two for the mounting screws). This
application is useful when mounting the tweeters to a
panel that has insufficient clearance behind it for the
tweeter’s magnet structure.
Flush-Mount: yields a custom-installed appear-
ance and requires a 1-1/2-inch (38 mm) diameter hole
to be cut in the vehicle panel, with at least 0.40-inch
(10 mm) of clearance behind the mounting surface
for the tweeter and up to 1.45-inch (37 mm) for the
stud bolts used to mount each tweeter.
TWEETER PROTECTION
The C1 crossover networks are equipped with
an advanced electronic tweeter protection circuit
designed to minimize the possibility of tweeter
failure. This electronic device monitors current going
to the tweeter and will disconnect the tweeter from
the signal when it senses overload. Should this occur
while listening to the audio system, simply reduce the
volume for a few seconds and the protection circuit
will reset itself automatically.
CROSSOVER NETWORK INSTALLATION
The crossover networks supplied with your C1
System should be installed in a dry location inside
your vehicle. DO NOT INSTALL THEM INSIDE
OF A DOOR! Doors often get wet on the inside,
which can damage your crossover networks and
could potentially damage your entire sound system.
Use plastic cable ties or a similar fastener to securely
mount each crossover to avoid coming loose in the
event of a collision, sudden jolt or repeated vibrations
during normal use. Make sure that your mounting
location will not cause damage to wiring or any other
vital component of your vehicle.
TWEETER CONNECTIONS
Run the wire leads from the crossovers to
the tweeter mounting locations and to the
speaker/amplifier outputs. Then connect the
harness wire leads to the speaker/amplifier
outputs and tweeters, observing correct
polarity. See Diagram C below for details.
WARNING
!!
It is absolutely vital that your component tweeter
is connected, as shown in Diagram C. Failure to
connect the tweeter as shown will result in damage
which is NOT covered under warranty. Only use
in-line filters clearly marked “C1-100cthp”.
Fr
om Woofer
or Amplier
Tweeter Crossover
Tweeter
DIAGRAM C:
Tweeter / Crossover Wiring
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio C1-690 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio C1-690 in the language / languages: English as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info