701256
4
Zoom out
Zoom in
Previous page
1/8
Next page
4 | JL Audio - C1-570x Owners Manual
WARNING
!!
Double check the clearance for both speakers
before proceeding. Many cars are different from
one side to the other!
Speaker Installation in Factory Locations:
Your new speakers have been designed to
install, without modifications, into most vehicles
with OEM speaker locations that accept a 5 x
7-inch (125 x 180 mm) speaker. The speaker
frames also have slotted mounting holes suitable
for installation into factory 6 x 8-inch speaker
locations. Many factory 5 x 7-inch speakers use
four mounting screws, which will line up with
the mounting holes on your C1-570x speakers.
Spacer adaptor rings are included to fit, bottom-
mount applications, if needed. Each spacer ring
can be placed on the front of the mounting
flange, in between the speaker and mounting
panel, as shown in Diagram A (page 5).
It is absolutely vital that the speaker frame
fits into the mounting hole cleanly. This must
be checked prior to tightening the screws. Never
force the frame into a hole that is too small, and
do not attempt to tighten the speaker onto an
uneven surface. This will damage your speakers.
The speaker should fit so that air does not leak
around the mounting flange. Air leaks will cause
a severe degradation in sound quality. Seal any air
leaks with an automotive-grade sealant material.
WARNING
!!
Hand-tighten the screws evenly in a criss-cross
pattern to avoid bending the speaker frame or
stripping the mounting screws.
INSTALLATION OVERVIEW
C1 speakers are designed for installation into
OEM speaker locations, mounted behind factory
panels/grilles. Depending on the equipment used
or design of your audio system, you may use the
factory speaker wires or run new speaker wires to
each speaker location. You will also need to run new
speaker wires if you elect to mount your speakers in
custom locations. Select the wiring method that is
appropriate for your audio system and equipment.
If you are unsure about this or any steps in the
installation process, please contact your JL Audio
dealer for installation help
Speaker Wiring:
If you will be using the factory speaker wires, it may
be necessary to change the terminations. This may
be accomplished by using an adaptor plug or simply
by cutting the factory connector off and using the
supplied crimp connectors to terminate the speaker
wires. The larger connector is for the positive terminal
and the smaller connector is for the negative terminal
of each C1-570x.
If you choose to run new speaker wires, protect all
wiring from sharp edges by carefully routing them,
securing them and using grommets and loom where
appropriate. If you are running wires into a door, use
existing factory wiring boots whenever possible. If
you are drilling new holes, file their edges and install
rubber grommets into each hole. Wires running into
car doors should be covered with a protective, flexible
PVC sleeve. Make sure that the wires will clear door
hinges and other structures in the door.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio C1-570x at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio C1-570x in the language / languages: English as an attachment in your email.

The manual is 0,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info