700444
8
Zoom out
Zoom in
Previous page
1/13
Next page
14 | JL Audio - HD600/4 Owners Manual
15
If you connect a load higher than 4Ω nominal
per channel in stereo mode (or 8Ω in bridged
mode), power will drop by half with every
doubling of impedance above 4Ω stereo / 8Ω
mono. If you connect a load lower than 1.
nominal per channel in stereo mode (or 3Ω in
bridged mode, the amplifier protection
circuitry activates a “safe” mode which reduces
amplifier power to protect the circuitry from
failure (the LED status indicator on the control
panel will light up amber to indicate that this
has happened). See page 16 for details.
Speaker loads below 1.5Ω nominal per channel
in stereo or 3Ω nominal in bridged mode are
not recommended and may cause the amplifier
output to distort excessively.
BRIDGING CONSIDERATIONS
Bridging is the practice of combining the
output of two amplifier channels to drive a single
load. When bridged, each channel produces
signals of equal magnitude, but opposite polarity.
The combined output of the two channels
provides twice the output voltage available from a
single channel. The HD600/4 has been designed
for bridging of its channel pairs without the need
for input inversion adaptors.
Rear Preouts
Remote
Level
Control
Front
Inputs
L
R
L
R
+12 VDC Ground Remote
To bridge a pair of channels, use the Left +
and Right – speaker connectors only
(the Left – and “Right +” remain unused).
Then connect a mono signal to both left and
right RCA inputs for that channel pair. This
requires an RCA “Y-Adaptor” (sold separately),
because a bridged pair of channels requires that
both amplifier channels of the bridged pair
receive input. Connection of only one RCA input
will result in reduced power output, increased
distortion and can cause the amplifier to overheat.
When bridged, each channel pair will
deliver optimum power into a 3-8Ω load.
Operating bridged channel pairs into a load
lower than 3Ω is not recommended.
Speaker Connector Plugs
To connect the speaker wires to the amplifier,
unplug the speaker connector plugs from the
amplifier chassis (pull back firmly) and back out
the set screws on each connector plug, using the
supplied 2.5 mm hex wrench. Strip 3/8 inch (10
mm) of insulation from the end of each wire and
insert the bare wire into the receptacle on the
speaker connector plug, seating it firmly so that
no bare wire is exposed. While holding each wire
in place, tighten each set screw firmly, taking care
not to strip the head of the screw.
For example, if you are using the HD600/4 in a
stand-alone bi-amplified mode, you may want the
HD-RLC to only affect the level of the subwoofer
channels. Setting the “Remote Level Control”
switch to the “Rear Ch. position accomplishes
this (provided the subwoofer system is connected
to the rear channels).
In other cases, you may want control of all
four channels at the same time, so you would
set the “Remote Level Control” switch to the
All Ch. position.
The RBC-1 Remote Bass Control used with
JL Audio Slash, Slash v2, e-Series, A-Series and
G-Series amplifiers is NOT compatible with the
HD Series amplifiers. If you attempt to connect
an RBC-1 to an HD amplifer, the control will
not work. You must use the HD-RLC controller.
SPEAKER OUTPUTS
The HD600/4 employs JL Audio’s exclusive
Regulated, Intelligent Power Supply (R.I.P.S.)
design. The operation of the R.I.P.S. system is
independent for each pair of channels. This
sophisticated power supply allows the amplifier to
produce its optimum power (150 watts x 4) over a
wide range of speaker impedances.
Rear Preouts
Remote
Level
Control
Front
Inputs
L
R
L
R
+12 VDC Ground Remote
Unlike conventional amplifiers that require
a specific impedance to produce optimum
power, the R.I.P.S.-equipped HD600/4 gives
you the freedom to use a variety of speaker
configurations that achieve final nominal
impedances between 1.5 – 4Ω per channel in
stereo (without sacrificing power output or sound
quality). When bridged, each channel pair will
optimize output at 300 watts between 3 – 8Ω.
The operation of the R.I.P.S. circuitry is
entirely automatic and adjusts itself every time the
amplifier is turned on. There are no user controls
to configure. The system operates through
multiple stages of impedance optimization,
choosing the stage most appropriate to the actual
impedance of the speakers you connect to it.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio 4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio 4 in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info