700444
4
Zoom out
Zoom in
Previous page
1/13
Next page
OWNER’S MANUAL
4-Channel Class-D Full-Range Amplifier
Thank you for purchasing a JL Audio amplifier for
your automotive sound system.
Your amplifier has been designed and manufactured to exacting
standards in order to ensure years of musical enjoyment in your vehicle.
For maximum performance, we highly recommend that you have
your new amplifier installed by an authorized JL Audio dealer. Your
authorized dealer has the training, expertise and installation equipment
to ensure optimum performance from this product. Should you
decide to install the amplifier yourself, please take the time
to read this manual thoroughly so as to familiarize yourself
with its installation requirements and setup procedures.
If you have any questions regarding the instructions in this
manual or any aspect of your amplifier’s operation, please contact your
authorized JL Audio dealer for assistance. If you need further assistance,
please call the JL Audio Technical Support Department
at (954) 443-1100 during business hours.
2 | JL Audio - HD600/4 Owners Manual
3
Cooling Efficiency Considerations:
Your JL Audio amplifier employs an
advanced type of heat management, called
RealSink™. This feature takes advantage of
convection and radiation effects to remove
heat from the amplifier circuitry. For optimum
cooling performance, the vertical heat sinks
located at the sides of the amplifier should be
exposed to as large a volume of air as possible.
Enclosing the amplifier in a small, poorly
ventilated chamber can lead to excessive heat
build-up and degraded performance. If an
installation calls for an enclosure around the
amplifier, we recommend that this enclosure
be ventilated with the aid of a fan. In normal
applications, fan-cooling is not necessary.
If mounting the amplifier under a seat,
make sure there is at least 1 inch (2.5 cm) of
space above the amplifier’s outer shell to permit
proper cooling.
Safety Considerations:
Your amplifier needs to be installed in a dry,
well-ventilated environment and in a manner
which does not interfere with your vehicle’s safety
equipment (air bags, seat belt systems, ABS brake
systems, etc.). You should also take the time to
securely mount the amplifier using appropriate
hardware so that it does not come loose in the
event of a collision or a sudden jolt to the vehicle.
Stupid Mistakes to Avoid:
Check before drilling any holes in your vehicle
to make sure that you will not be drilling
through a gas tank, brake line, wiring harness or
other vital vehicle system.
Do not run system wiring outside or underneath
the vehicle. This is an extremely dangerous
practice which can result in severe damage to
your vehicle and person.
Protect all system wires from sharp metal
edges and wear by carefully routing them,
tying them down and using grommets and
loom where appropriate.
Do not mount the amplifier in the engine
compartment, under the vehicle, on the roof
or in any other area that will expose the
amplifier circuitry to the elements.
PROTECT YOUR HEARING!
We value you as a long-term customer. For
that reason, we urge you to practice restraint in
the operation of this product so as not to damage
your hearing and that of others in your vehicle.
Studies have shown that continuous exposure to
high sound pressure levels can lead to permanent
(irreparable) hearing loss. This and all other
high-power amplifiers are capable of producing
such high sound pressure levels when connected
to a speaker system. Please limit your continuous
exposure to high volume levels.
While driving, operate your audio system in
a manner that still allows you to hear necessary
noises to operate your vehicle safely (horns,
sirens, etc.).
SERIAL NUMBER
In the event that your amplifier requires
service or is ever stolen, you will need to
have a record of the product’s serial number.
Please take the time to enter that number in
the space provided below. The serial number
can be found on the bottom panel of the
amplifier and on the amplifier packaging.
Serial Number:
INSTALLATION APPLICATIONS
This amplifier is designed for operation in
vehicles with 12V, negative-ground electrical
systems. Use of this product in vehicles with
positive ground and/or voltages other than 12V
may result in damage to the product and will void
the warranty.
This product is not certified or approved for
use in aircraft.
Do not attempt to “bridge” the outputs of this
amplifier with the outputs of a second amplifier,
including an identical one.
PLANNING YOUR INSTALLATION
It is important that you take the time to read
this manual and that you plan out your
installation carefully. The following are some
considerations that you must take into account
when planning your installation.
Input Sensitivity
Control
(pg. 10)
Power Status
Indicator
(pg. 16)
Filter Mode
Selection
(pg. 11)
Filter Slope
Selection
(pg. 11)
Filter Frequency
Selector
(pg. 11)
Input Sensitivity
Control
(pg. 10)
Filter Mode
Selection
(pg. 11)
Filter Slope
Selection
(pg. 11)
Input Mode
Selection
(pg. 9)
Preouts From
Selection
(pg. 13)
Filter Frequency
Selector
(pg. 11)
Input Voltage
Selection
(pg. 10)
Remote Level
Control
Selection
(pg. 13)
Input Voltage
Selection
(pg. 10)
Rear Preouts
Remote
Level
Control
Front
Inputs
L
R
L
R
+12 VDC Ground Remote
Chassis Ground
Connector
(pgs. 6-7)
Front Left & Right
Channel Input Jacks
(pg. 9)
Left & Right Preamp
Output Jacks
(pg. 13)
Rear Left & Right
Channel Input Jacks
(pg. 9)
Rear
Speaker Outputs
(pgs. 14-15)
Front
Speaker Outputs
(pgs. 14-15)
Jack for
Remote Level
Control Knob
(pg. 13)
Remote Turn-On
Connector
(pgs. 6-7)
+12 V Power
Connector
(pgs. 6-7)
4 | JL Audio - HD600/4 Owners Manual
5
TYPICAL INSTALLATION SEQUENCE
The following represents the sequence for
a typical amplifier installation, using an
aftermarket source unit or OEM Interface
processor (like the CleanSweep® CL441dsp).
Additional steps and different procedures may
be required in some applications. If you have
any questions, please contact your authorized
JL Audio dealer for assistance.
1) Disconnect the negative battery post
connection and secure the disconnected cable
to prevent accidental re-connection during
installation. This step is not optional!
2) Run power wire from the battery location to
the amplifier mounting location, taking care
to route it in such a way that it will not be
damaged and will not interfere with vehicle
operation. 4 AWG is recommended for wire
runs greater than 72 inches (180 cm) in
length. Use of 8 AWG power wire is acceptable
for shorter runs, such as from a power
distribution block to the amplifier or from a
trunk-mounted battery. Use a 2 AWG or 1/0
AWG main power wire with a fused power
distribution block when additional amplifiers
are being installed with the HD600/4 and
powered from the same main power wire.
3) Connect power wire to the positive battery
post. Fuse the wire with an appropriate fuse
block (and connectors) within 18 inches (45
cm) wire length of the positive battery post.
This fuse is essential to protect the vehicle.
Do not install the fuse until the power wire
has been connected to the amplifier.
4) Run signal cables (RCA cables) and remote
turn-on wire from the source unit or interface
processor to the amplifier mounting location.
5) Run speaker wire from the speaker systems to
the amplifier mounting location.
6) Find a good, solid, bare metal grounding
point close to the amplifier and connect the
negative power wire to it using appropriate
hardware. Use minimum 8 AWG power wire,
no longer than 36 inches (90 cm) or 4 AWG
wire up to 60 inches (150 cm) long from the
amplifier to the ground connection point. In
some vehicles, it may be necessary to upgrade
the batterys ground wire as well. (See page 7
for important notice).
7) Securely mount the amplifier using
appropriate hardware. (See page 8 for detailed
mounting instructions).
8) Connect the remote turn-on wire and the
positive and negative power wires to the
amplifier’s power connector plug. Then insert
the power connector plug into the amplifier’s
power connector receptacle, pushing firmly.
9) Connect the RCA input cables
to the amplifier.
10) Connect the speaker wires to the speaker
connector plugs and insert the plugs firmly
into the speaker connector receptacles.
11) Carefully review the amplifier’s control
settings to make sure that they are set
according to the needs of the system.
12) Install power wire fuse (50A for a
single HD600/4) and reconnect the negative
battery post terminal.
13) Turn on the source unit at a low level
to double-check that the amplifier is
configured correctly. Resist the temptation
to crank it up until you have verified the
control settings.
14) Make necessary adjustments to the input
sensitivity controls to obtain the right
overall output and the desired balance
in the system. See Appendix C (pages 18, 19)
for the recommended input sensitivity
setting method.
15) Enjoy the fruits of your labor with your
favorite music.
PRODUCT DESCRIPTION
The JL Audio HD600/4 is a very powerful
and compact four-channel, full-range amplifier
utilizing patented Single Cycle Control
Class D technology for all channels. This
groundbreaking technology delivers reference-
grade sonic performance while requiring
far less current from the vehicle’s electrical
system than a conventional amplifier.
JL Audio’s exclusive R.I.P.S. power supply
design optimizes the output of each channel pair
for any impedance between 1.5 and 4 ohms per
channel (3-8 ohms bridged) allowing you to get
full use of the HD600/4’s performance capabilities
with a wide range of speaker systems.
The tightly regulated power supply design also
means that the HD600/4’s clean power output
capability remains stable over a wide range of
vehicle voltages, resulting in enhanced fidelity.
The HD600/4 flexible, studio-grade signal
processing allows it to be deployed in a wide
range of system applications:
1) As a four-channel (150W x 4) full-range
amplifier, delivering full-range signals to two
separate stereo speaker systems (front and rear,
for example).
2) As a powerful (150W x 4) four-channel satellite
amplifier in a bi-amplified system, delivering
high-passed signals to front and rear speaker
systems. Preamp outputs permit connection of a
separate amplifier to drive the subwoofer system.
3) As a 600W full-system amplifier in
bi-amplified mode with one channel pair
driving subwoofers in low-pass mode (150W
x 2 or 300W x 1) and the other channel pair
driving main speakers in high-pass mode
(150W x 2).
4) As a very powerful (300W x 2) full-range
amplifier, delivering full-range signals to a
stereo speaker system.
5) As a very powerful (300W x 2) two-channel
satellite amplifier in a bi-amplified system,
delivering high-passed signals to a stereo
speaker system. Preamp outputs permit
connection of a separate amplifier to drive the
subwoofer system.
6) As a powerful (300W x 2) two-channel
subwoofer amplifier in a bi-amplified system,
delivering low-passed signals to a dual
subwoofer system. Preamp outputs permit
connection of a separate amplifier to drive the
satellite speakers.
The HD600/4’s flexible input and crossover
sections permit operation with a wide variety of
source units and system configurations. It can be
operated with a single pair of stereo inputs or with
separate inputs for its front and rear channels.
The HD600/4’s preamp output can send pass-
through signals from the Front Inputs only or it
can sum all four input channels to feed a non-
fading signal to a separate subwoofer amplifier.
As we said, it’s very flexible.
6 | JL Audio - HD600/4 Owners Manual
7
Ground Connection
The chassis ground connection must be
made using 4 AWG or 8 AWG pure copper
wire and should be kept as short as possible,
while accessing a solid piece of sheet metal
in the vehicle. The surface of the sheet metal
should be sanded at the contact point to create
a clean, metal-to-metal connection between
the chassis and the termination of the ground
wire with a brass or copper power ring. For
optimal grounding, we recommend the
use of a JL Audio ECS master ground lug
(XB-MGLU). Alternatively, a sheet metal
screw or bolt can be used with a star washer.
Many vehicles employ small (10 AWG - 6 AWG)
wire to ground the battery to the vehicle chassis
and to connect the alternators positive
connection to the battery. To prevent voltage
drops, these wires should be upgraded to 4
AWG pure copper wire when installing amplifier
systems with main fuse ratings above 60A.
Turn-On Wire
The HD600/4 uses a conventional +12V remote
turn-on wire, typically controlled by the source
units remote turn-on output. The amplifier will
turn on when +12V is present at its Remote
input and turn off when +12V is switched off. If
a source unit does not have a dedicated remote
turn-on output, the amplifier’s turn-on lead can
be connected to +12V via a switch that derives
power from an ignition-switched circuit.
The HD600/4’s Remote turn-on connector
is designed to accept 18 AWG – 12 AWG wire. 18
AWG is more than adequate for this purpose.
To connect the remote turn-on wire to the
amplifier, first back out the set screw on the
bottom of the Power Connector Plug, using the
supplied hex wrench. Strip 1/2 inch (12mm) of
wire and insert the bare wire into the receptacle,
seating it firmly so that no bare wire is exposed.
When using smaller wire, it may be necessary to
strip 1 inch of insulation from the wire and fold
the bare wire in half prior to insertion. While
holding the wire in the terminal, tighten the
set screw firmly using the supplied 2.5 mm hex
wrench, taking care not to strip the head of the
screw and making sure that the wire is firmly
gripped by the set screw.
Amplifier Power Connector Plug
To connect the power wires and the remote
turn-on wire to the amplifier, unplug the power
connector plug from the amplifier chassis (pull
back firmly) and back out the set screws on
the connector plug, using the supplied 4 mm
hex wrench for the +12 VDC and Ground
connections and the supplied 2.5 mm hex wrench
for the Remoteconnection. Strip 3/8 inch (10
mm) of insulation from the end of each wire and
insert the bare wire into the receptacle on power
connector plug, seating it firmly so that no bare
wire is exposed. While holding each wire in place,
tighten each set screw firmly, taking care not to
strip the head of the screw.
Never make power connections with a “live”
wire. Always disconnect the negative battery
post before making any connections or
adjustments to a 12V power connection!
POWER AND TURNON CONNECTIONS
Before installing the amplifier, disconnect the
negative (ground) wire from the vehicle’s battery.
This will prevent accidental damage to the system,
the vehicle and your body during installation.
Rear Preouts
Remote
Level
Control
Front
Inputs
L
R
L
R
+12 VDC Ground Remote
+12V Battery Connection
You will need to connect a power wire to
the vehicles positive battery terminal, using
an appropriate power ring or specialized
battery terminal connector, such as the JL
Audio XB-BTU or XD-BTS. This connection
must be tight and corrosion-free to ensure
proper connectivity. This wire MUST be fused
appropriately for safety. Any power wires run
through metal barriers (such as firewalls), must
be protected with a high quality insulating
grommet to prevent damage to the insulation
of the wire. Failure to do so may result in a
dangerous short circuit.
Power Wire Requirements
The HD600/4’s +12 VDC and Ground
connections are designed to accept 4 AWG power
wire. 4 AWG pure copper wire is recommended
for any power wire run longer than 72 inches (180
cm). For runs shorter than 72 inches, 8 AWG pure
copper power wire is acceptable.
If you are installing the HD600/4 with other
amplifiers and wish to use a single main power
wire, use 2 AWG or 1/0 AWG pure copper
wire as a main power wire. This 2 AWG or
1/0 AWG power wire should terminate into a
fused distribution block mounted as close to the
amplifiers as possible and should connect to the
HD600/4 with 4 AWG or 8 AWG pure copper
power wire.
Please note that lower AWG numbers mean
bigger wire and vice-versa (1/0 AWG is the largest,
2 AWG is smaller, then 4 AWG, then 8 AWG, etc.).
We do not recommend the use of “copper-
clad aluminum wire” or “CCA” wire because
this wire is significantly less conductive than
pure copper wire. Only use pure copper power
wire, such as JL Audio’s Premium Power Wire.
Tinned copper wire (silver color) is acceptable
as the tin-plating is only a very minor
component of the wire.
Fuse Requirements
The installation of a fuse on the main power
wire, within 18 wire inches (45 cm) of the positive
battery terminal is vital to protect the wire and
the vehicle from fire in the event of a collision
or short-circuit. The fuse value at each power
wire should be just high enough for all of the
equipment being run from that power wire. Do
not use a fuse with a value that far exceeds the
total fuse rating of the electronics connected to
the wire.
If only the HD600/4 is being run from that
power wire, we recommend a 50A fuse be used.
AGU (big glass fuse). AFS (small blade fuse)
or MaxiFuse™ (big plastic-body fuse) types are
recommended.
If other amplifiers are also being powered from
a main power wire and exceed 80 amps in total
fuse rating, we recommend the use of an ANL
(large-blade) fuse and holder at the battery plus a
fused distribution block near the amplifiers. Each
amplifier must be fused independently at the
outputs of the fused power distribution block. We
recommend appropriately rated MaxiFuse™ fuses
and a JL Audio fused distribution block.
Please consult with your JL Audio
dealer to make sure that the wire, fuse
holder and fuse ratings are appropriate
for your system’s needs. The safety of
your installation depends on appropriate
power connections and fuse protection.
8 | JL Audio - HD600/4 Owners Manual
9
AMPLIFIER INPUTS
The HD600/4 has two separate input sections,
one for the “Front” left and right channels and
another for the “Rear” left and right channels.
Each section consists of a pair of RCA-type input
jacks on the Connection Panel of the amplifier
and a pair of input controls on the Control Panel
of the amplifier: an “Input Voltage” switch and an
Input Sens.” rotary control.
Rear
Preouts
Remote
Level
Control
Front
Inputs
L
R
L
R
+12 VDC Ground Remote
“INPUT MODE” SWITCH
The Control Panel houses an Input
Mode switch located under the “General Setup
heading. This switch allows operation of all four
amplifier channels with only one pair of input
signals or with independent front and rear input
signal pairs.
To use separate inputs for the “Front and
“Rear” amplifier sections, (in order to permit
front-to-rear fading, for example), select 4 Ch.
on the Input Mode switch. In this mode, you
must connect separate pairs of input cables to the
“Front and “Rear amplifier inputs.
To operate all four channels of the HD600/4
with a single pair of stereo inputs, select the
2 Ch. position on the Input Mode
switch and connect a single pair of input
cables to the “Frontinput jacks only. In
this mode, the amplifier will route the
signals connected to the “Front inputs to
the Front and Rear amplifier channels.
CHANNEL CONTROL SECTIONS
Flanking the “General Setup” section
on the Control Panel of the amplifer are
two sets of identical controls: one for the
“Rear Channel Controls” (on the left side)
and one for the “Front Channel Controls
of the amplifier (on the right side).
In each of these sections you will find an
“Input Voltage” range switch and a rotary
control labeled “Input Sens.” (Input Sensitivity).
These controls are designed to match the input
sensitivity of the HD600/4 to the specific signal
source that is feeding it and must be adjusted,
with care, following the procedures outlined in
this manual. Failure to make correct adjustments
can result in weak output, excessive distortion
and/or undesirable noise in the audio output of
the amplifier!
Note: The Channel Control sections also house
“Filter Mode, “Filter Slope” and “Filter Freq.”
controls. These are crossover filter controls
and will be discussed in the next section of this
manual. This section will explain the Input
Controls only.
AMPLIFIER MOUNTING OPTIONS
The HD600/4 has two mounting options to
ease in installation.
Standard Mounting
The standard method of mounting requires
removal of the four corner caps with the 3/16-inch
hex wrench included with your amplifier. Using
appropriate mounting screws (not included),
secure the amplifier in all four corners and
replace the corner caps.
Lateral Mounting Feet
Lateral Mounting Feet are also included with
your HD600/4 to provide an alternative mounting
option. Each mounting foot should be attached
to the bottom of the amplifier by screwing the
provided bolt into the bottom of the amplifier and
up into the corner cap with the supplied 1/8-inch
hex wrench. Next, using appropriate mounting
screws (not included), secure the amplifier by its
four Lateral Mounting Feet.
Check before drilling any holes in your vehicle
to make sure that you will not be drilling
through a gas tank, brake line, wiring harness
or other vital vehicle system.
CONTROL PANEL SECURITY COVER
The HD600/4 features a Control Panel Security
Cover. When installed, the cover ensures that
your amplifier settings are not accidentally
changed while creating a clean aesthetic for the
amplifier and your installation. The control panel
security cover is pre-installed at the factory and
must be temporarily removed for access to the
controls described throughout this manual.
The security cover is secured by a single 2.5
mm hex-head screw at the far right of the panel.
Loosen the hex-head screw to release the security
cover (it is not necessary to completely remove the
screw). To re-install the security cover once all
adjustments have been made, insert the tongue on
the covers left edge into the groove where the left-
side heatsink meets the control panel, hinge the
panel closed and secure the screw using the
supplied 2.5 mm hex wrench. Do not overtighten
the screw.
10 | JL Audio - HD600/4 Owners Manual
11
CROSSOVER CONTROLS
Crossovers are groups of electronic filters
designed to control the frequency ranges
that each speaker in a system will be tasked
with reproducing. Proper crossover setup is
critical to sound quality and reliability.
The HD600/4 has two individual filters,
one for the “Front channels and the
other for the “Rear channels. Each can be
configured as a high-pass filter (attenuates low
frequencies) or as a low-pass filter (attenuates
high frequencies). Additionally, the user can
select from a shallow (12dB/octave) filter slope
or a more aggressive (24dB/octave) slope.
Each Channel Control section contains
identical crossover filter controls.
1) Filter Mode Control: this switch allows you
to configure the filter for that Channel Pair
into one of two filter types.
Off: Defeats the filter completely, allowing
the full range of frequencies present at the
inputs to feed that pair of channels. This
is useful for systems utilizing outboard
crossovers or requiring full-range reproduction
from that pair of channels.
HP (High-Pass): Configures the
CH 1&2 filter to attenuate frequencies
below the selected filter frequency.
Useful for connection of component
speakers in a bi-amplified system.
LP (Low-Pass): Attenuates frequencies
above the selected filter frequency.
Useful for connection of subwoofer(s)
in a bi-amplified system.
2) Filter Slope Control: This switch allows you
to select from two filter slopes.
12dB: Configures the filter to attenuate
frequencies above or below the selected
filter frequency at a rate of 12 dB per octave
(Butterworth alignment).
24dB: Configures the filter to attenuate
frequencies above or below the selected
filter frequency at a rate of 24 dB per octave
(Linkwitz-Riley alignment).
Depending on the speaker system and the
vehicle, different filter slopes may be required to
produce a smooth transition between the sound
of different speakers in the system.
In high-pass mode, the sharper 24dB setting
will do a better job of protecting small speakers
with limited power handling. In low-pass
mode, the 24dB setting can also help by more
aggressively removing lower midrange output
from a subwoofer system.
The shallower 12dB octave setting
allows for more output overlap between
the speakers being crossed over. In many
cases, this will result in a smoother “blend
or transition between speaker systems.
Experiment to find the slope or combination
of slopes which best matches the acoustic
requirements of your system.
3) Filter Freq. (Hz) Control:
This control selects the frequency at which the
filter begins to attenuate the signal and refers
specifically to the frequency at which output
has been attenuated by -3dB.
The filter frequency markings surrounding this
rotary control are for reference purposes and are
generally accurate to within 1/3 octave or better. If
you would like to select the filter cutoff frequency
with a higher level of precision, consult the charts
in Appendix B (page 18) of this manual.
“Input Voltage” Switch
A wide range of signal input voltages can
be accommodated by each of the HD600/4’s
differential-balanced inputs (200mV – 8V RMS).
This wide range is split up into two sub-ranges,
accessible via the Input Voltage switches located
in each input section of the amplifier. Be aware
that each input section’s Input Voltage switch
will have to be configured, regardless of how many
input cables are actually feeding the amplifier.
The Low position on each Input
Voltage switch selects an input sensitivity
range between 200mV and 2V. This means that
the Input Sens. rotary control will operate
within that voltage window. If you are using
an aftermarket source unit, with preamp-level
outputs, this is most likely the position that
you will use (regardless of what voltage output
capability is claimed by the source unit).
The High position on each Input Voltage
switch selects an input sensitivity range between
800mV and 8V. This is for use with speaker-level
outputs from source units and small amplifiers
found in many OEM (factory-installed) systems.
To use speaker-level sources, splice the speaker
output wires of the source unit or small amplifier
onto a pair of RCA plugs for each input pair
or use the JL Audio ECS Speaker Wire to RCA
adaptor (XB-CLRAIC2-SW).
The output of the amplifier decreases for a
given input voltage when the “Input Range”
switch is placed in the “High” position. The
output increases with the switch in the “Low
position. While this may sound counter-
intuitive, it is correct as described.
“Input Sens.” Control
Located next to the Input Voltage switch
in each input section is a rotary control labeled
Input Sens.. Once the appropriate Input
Voltage range has been selected, this control
can be used to match the source unit’s output
voltage to the input stage of each pair of amplifier
channels for maximum clean output. Rotating the
control clockwise will result in higher sensitivity
(louder for a given input voltage). Rotating the
control counter-clockwise will result in lower
sensitivity (quieter for a given input voltage). To
properly set each pair of amplifier channels for
maximum clean output, please refer to Appendix
C (pages 18, 19) in this manual.
After using this procedure, you can then adjust
the relative level of each channel pair by adjusting
the input sensitivity downward on either or both
channel pairs, if they require attenuation to
achieve the desired system balance.
Do not increase the Input Sens. setting for
any amplifier in the system beyond the maximum
level established during the procedure outlined in
Appendix C (pages 18, 19). Doing so will result in
audible distortion and possible speaker damage.
Be aware that both Input Sens. adjustments
will have to be made, regardless of how many
input cables are feeding the amplifier. These
controls will allow you to set the appropriate
relative levels for the “Front channels relative
to the “Rear channels and any other amplifier
channels in the system.
12 | JL Audio - HD600/4 Owners Manual
13
PREAMP OUTPUTS
The HD600/4 incorporates a pass-through
preamp output section, so that additional
amplifiers can easily be connected to the same
signal(s) feeding the HD600/4. These preamp
output signals are accessible via a stereo pair
of RCA-type jacks, labeled “Preouts”, on the
Connection Panel.
Rear
Preouts
Remote
Level
Control
Front
Inputs
L
R
L
R
+12 VDC Ground Remote
The term “pass-through” refers to the fact that
the Preamp Output signals are not affected by any
crossover filter or input sensitivity setting selected
on the HD600/4 (if the input signal is full-range,
the Preamp Output will be full-range). These
preamp output signals are buffered to prevent
noise and are always preamp level, regardless of
the level of signals feeding the HD600/4’s inputs.
The pass-through Preamp Outputs can be
configured two different ways using the switch
labeled Preouts From in the General Setup
section of the Control Panel.
1) Front: The preamp output delivers the same
signal that is connected to the HD600/4’s
Front Inputs”. This mode is useful for
feeding a subwoofer amplifier when the
HD600/4 is being used to drive front and rear
speaker systems. In this mode, the preamp
output level will track with the signal level
of the front input signals, allowing the user
to fade the rear channels in and out, without
affecting the subwoofer level.
3) F+R (Front + Rear): This mode delivers a
sum of the signals being fed to the Front
Inputs” and the Rear Inputs of the
amplifier. When the HD600/4 is being used
to drive front and rear speaker systems, this
preamp output mode will deliver a summed
front/rear signal to the subwoofer amplifier,
while permitting fading of the front and rear
speaker systems from the source unit.
REMOTE LEVEL CONTROL OPTIONAL
With the addition of the optional Remote Level
Control (HD-RLC), you can control the volume
of one or both channel pairs of the HD600/4
from the front of the vehicle. This is useful for
subwoofer level control or even as a master
volume control for the system.
The HD-RLC connects to the jack labeled
“Remote Level Control” on the Connection
Panel of the amplifier using a standard telephone
cable (supplied with the HD-RLC).
If desired, multiple HD amplifiers can be
controlled from a single HD-RLC controller
using a simple phone line “splitter” and multiple
phone cables.
Rear
Preouts
Remote
Level
Control
Front
Inputs
L
R
L
R
+12 VDC Ground Remote
When connected to the amplifier, the HD-RLC
operates as follows. At full counter-clockwise
rotation, the audio will mute completely. At full
clockwise rotation the level will be the same as if
the HD-RLC was not connected at all. In other
words, it operates strictly as a level attenuator.
Depending on the application, you may want
the HD-RLC to only affect one channel pair or
both channel pairs. A switch labeled “Remote
Level Control” in the “General Setup” Section
of the Control Panel allows you to determine
whether the HD-RLC affects the level of all
channels All Ch. or only the rear channels
“Rear Ch.
BIAMPLIFIED SYSTEMS
Bi-amplified systems are defined as systems
in which separate amplifier channels drive low-
frequency (LF) and high-frequency (HF) speakers
and are separately filtered to send appropriate
frequency ranges to each speaker system.
The most common application of
bi-amplification in mobile audio is to drive a
subwoofer system from one or more amplifiers or
channels and component speakers from separate
amplifiers or channels.
The HD600/4 can be configured to drive a
bi-amplified system by itself or with a separate
subwoofer amplifier.
Bi-Amplified System with one HD600/4
In this configuration, the “Rear channels
of the HD600/4 will drive subwoofers
(stereo 150W x 2 or bridged 300W x 1) with
low-pass filtering. The “Front channels
will drive component speakers in stereo
(150W x 2) with high-pass filtering.
Crossover Setup for Bi-Amplified System
with one HD600/4:
Once the input sections have been configured
appropriately, go to the Rear Channel Controls”
Section. Select LP (low-pass) on the Filter
Mode switch and 12dB or 24dB on the
Filter Slope switch and an appropriate Filter
Freq.” (80-90 Hz is a good starting point).
Next, turn your attention to the Front
Channel Controls” Section. and select HP
(high-pass) on the Filter Mode switch and
12dB or 24dB on the Filter Slope
switch and an appropriate Filter Freq.
(again, 80-90 Hz is a good starting point).
After proper adjustment of the Front and
Rear channel Input Range and Input
Sens. controls using the method shown
in Appendix C (pages 18, 19), you can
fine tune filter frequencies and slopes and
attenuate either pair of channels to achieve
proper balance. For precise filter frequency
information refer to Appendix B (page 18).
Bi-Amplified System with one
HD600/4 in four-channel mode and
a separate subwoofer amplifier
This configuration requires that the
separate subwoofer amplifier has a built-in
low-pass filter. In this configuration, the
“Front channels of the HD600/4 will drive
front component speakers (stereo 150W x 2)
with high-pass filtering. The “Rear” channels
will drive rear component speakers in stereo
(150W x 2) with high-pass filtering.
The separate subwoofer amplifier will drive the
subwoofer system with low-pass filtering (select a
filter frequency of 80-90 Hz to start). The inputs
of the subwoofer amplifier can be fed from the
HD600/4’s preamp output or from a dedicated
subwoofer output on the source unit.
Crossover Setup for Bi-Amplified System with one
HD600/4 and a separate subwoofer amplifier:
Once the input and preamp output sections
have been configured appropriately, go to the
Front Channel Controls” Section. Select HP
(high-pass) on the “Filter Modeswitch and
12dB or 24dB on the “Filter Slope” switch
and an appropriate Filter Freq. (80-90 Hz is a
good starting point).
Next, turn your attention to the Rear
Channel Controls” Section and select HP
(high-pass) on the Filter Mode switch and
12dB or 24dB on the Filter Slope switch
and an appropriate Filter Freq. (again, 80-90 Hz
is a good starting point).
After proper adjustment of the HD600/4’s and
the subwoofer amplifier’s Input Range and
Input Sens., you can fine tune filter frequencies
and slopes and attenuate either pair of channels
to achieve proper balance. For proper adjustment
of the Input Sens. controls of the HD600/4 use
the method shown in Appendix C (pages 18, 19).
For precise filter frequency information for the
HD600/4 refer to Appendix B (pages 18). Refer to
the subwoofer amplifier owner’s manual for its
proper adjustment levels.
14 | JL Audio - HD600/4 Owners Manual
15
If you connect a load higher than 4Ω nominal
per channel in stereo mode (or 8Ω in bridged
mode), power will drop by half with every
doubling of impedance above 4Ω stereo / 8Ω
mono. If you connect a load lower than 1.
nominal per channel in stereo mode (or 3Ω in
bridged mode, the amplifier protection
circuitry activates a “safe” mode which reduces
amplifier power to protect the circuitry from
failure (the LED status indicator on the control
panel will light up amber to indicate that this
has happened). See page 16 for details.
Speaker loads below 1.5Ω nominal per channel
in stereo or 3Ω nominal in bridged mode are
not recommended and may cause the amplifier
output to distort excessively.
BRIDGING CONSIDERATIONS
Bridging is the practice of combining the
output of two amplifier channels to drive a single
load. When bridged, each channel produces
signals of equal magnitude, but opposite polarity.
The combined output of the two channels
provides twice the output voltage available from a
single channel. The HD600/4 has been designed
for bridging of its channel pairs without the need
for input inversion adaptors.
Rear Preouts
Remote
Level
Control
Front
Inputs
L
R
L
R
+12 VDC Ground Remote
To bridge a pair of channels, use the Left +
and Right – speaker connectors only
(the Left – and “Right +” remain unused).
Then connect a mono signal to both left and
right RCA inputs for that channel pair. This
requires an RCA “Y-Adaptor” (sold separately),
because a bridged pair of channels requires that
both amplifier channels of the bridged pair
receive input. Connection of only one RCA input
will result in reduced power output, increased
distortion and can cause the amplifier to overheat.
When bridged, each channel pair will
deliver optimum power into a 3-8Ω load.
Operating bridged channel pairs into a load
lower than 3Ω is not recommended.
Speaker Connector Plugs
To connect the speaker wires to the amplifier,
unplug the speaker connector plugs from the
amplifier chassis (pull back firmly) and back out
the set screws on each connector plug, using the
supplied 2.5 mm hex wrench. Strip 3/8 inch (10
mm) of insulation from the end of each wire and
insert the bare wire into the receptacle on the
speaker connector plug, seating it firmly so that
no bare wire is exposed. While holding each wire
in place, tighten each set screw firmly, taking care
not to strip the head of the screw.
For example, if you are using the HD600/4 in a
stand-alone bi-amplified mode, you may want the
HD-RLC to only affect the level of the subwoofer
channels. Setting the “Remote Level Control”
switch to the “Rear Ch. position accomplishes
this (provided the subwoofer system is connected
to the rear channels).
In other cases, you may want control of all
four channels at the same time, so you would
set the “Remote Level Control” switch to the
All Ch. position.
The RBC-1 Remote Bass Control used with
JL Audio Slash, Slash v2, e-Series, A-Series and
G-Series amplifiers is NOT compatible with the
HD Series amplifiers. If you attempt to connect
an RBC-1 to an HD amplifer, the control will
not work. You must use the HD-RLC controller.
SPEAKER OUTPUTS
The HD600/4 employs JL Audio’s exclusive
Regulated, Intelligent Power Supply (R.I.P.S.)
design. The operation of the R.I.P.S. system is
independent for each pair of channels. This
sophisticated power supply allows the amplifier to
produce its optimum power (150 watts x 4) over a
wide range of speaker impedances.
Rear Preouts
Remote
Level
Control
Front
Inputs
L
R
L
R
+12 VDC Ground Remote
Unlike conventional amplifiers that require
a specific impedance to produce optimum
power, the R.I.P.S.-equipped HD600/4 gives
you the freedom to use a variety of speaker
configurations that achieve final nominal
impedances between 1.5 – 4Ω per channel in
stereo (without sacrificing power output or sound
quality). When bridged, each channel pair will
optimize output at 300 watts between 3 – 8Ω.
The operation of the R.I.P.S. circuitry is
entirely automatic and adjusts itself every time the
amplifier is turned on. There are no user controls
to configure. The system operates through
multiple stages of impedance optimization,
choosing the stage most appropriate to the actual
impedance of the speakers you connect to it.
16 | JL Audio - HD600/4 Owners Manual
17
“STATUS” LED / PROTECTION CIRCUITRY
There is a single multi-color LED on the
control panel of the amplifier to indicate the
amplifier’s operating status. This LED’s behavior
is as follows:
1) Flashing Green: amplifier is powering up,
audio output is muted.
2) Constant Green: amplifier is on and
functioning normally, audio output is active.
3) Constant Red: lights to indicate that the
amplifier has exceeded its safe operating
temperature, putting the amplifier into a
self-protection mode, which reduces the
peak power output of the amplifier. The red
light will turn green and the amplifier will
return to full-power operating mode when its
temperature returns to a safe level.
3) Constant Amber (yellow): lights to indicate
that the impedance of the speaker load
connected to the amplifier is lower than
the optimum load impedance range for the
amplifier. When this light is on, a protection
circuit engages and reduces the power output
of the “Front or the “Rear channels,
depending on which channel is experiencing
the problem. The amber indicator will also
light when a short-circuit is detected in the
speaker wiring (this can be a short between the
positive and negative speaker wires or between
either speaker wire and the vehicle chassis).
This can be used to diagnose a short-circuit by
only connecting one of the amplifier sections
at a time (“Front or “Rear” channels). The
amber LED will light when you connect the
section that is experiencing the problem and
turn the volume up.
4) Alternating Red and Green: lights to indicate
that the amplifier is experiencing a fault
that may require service of the amplifier, its
wiring or the vehicle’s charging system. Audio
is muted when this fault occurs. The most
likely cause of this fault is a low supply voltage
condition. If battery voltage drops below 8.5
volts at any point, the amplifier (except for the
“Status” LED) will shut itself off to protect itself
and the vehicles charging system. If the voltage
drops below 6 volts, the “Status” LED will also
turn off.
The amplifier will turn back on automatically
when voltage climbs back above 9 volts. This
shut-down and turn-on behavior may happen
in a rapid cycle when bass-heavy program
material causes a weak charging system to
momentarily dip too low. If this is happening
in your system, have your charging system
inspected to make sure it is working properly.
If no problem is found with the supply
voltage to the amplifier and you are
still seeing alternating Red and Green
on the “Status” LED, it is likely that the
amplifier is suffering from an internal
fault that requires factory service.
For more information on troubleshooting this
amplifier, refer to Appendix D (pages 20, 21).
SERVICING YOUR JL AUDIO AMPLIFIER
If your amplifier fails or malfunctions, please
return it to your authorized JL Audio dealer so
that it may be sent in to JL Audio for service.
There are no user serviceable parts or fuses inside
the amplifier. The unique nature of the circuitry
in the JL Audio amplifiers requires specifically
trained service personnel. Do not attempt
to service the amplifier yourself or through
unauthorized repair facilities. This will not only
void the warranty, but may result in the creation
of more problems within the amplifier.
If you have any questions about the installation or
setup of the amplifier not covered in this manual,
please contact your dealer or technical support.
JL Audio Technical Support:
(954) 443-1100
9:00 AM – 5:30 PM (Eastern Time Zone)
Monday - Friday
APPENDIX A:
HD600/4 Specifications
Amplifier Topology: Class D, switching type with
patented Single-Cycle Control™ technology.
Power Supply: Pulse width modulation-regulated
switching power supply
Recommended Fuse Value / Type: 50A (AGU or
MaxiFuse™)
Rated Power (Stereo):
150W RMS x 4 @ 1.5-4Ω (11V - 14.5V)
Rated Power (Bridged):
300W RMS x 2 @ 3-8Ω (11V - 14.5V)
THD at Rated Power: <0.03% @ 4Ω per channel
(Average at 1 kHz)
Signal to Noise Ratio (20 kHz Bandwidth):
Referred to Rated Power: 110 dBA
Referred to 1 Watt: 88.2 dBA
Frequency Response: 6 Hz - 30 kHz (+0, -1dB)
Damping Factor:
300 @ 4Ω per ch. / 50 Hz
150 @ 2Ω per ch. / 50 Hz
Crossover Filters:
Filter Sets: Two (Front Channel and Rear Channel)
Filter Type: State-variable, 12 dB/octave Butterworth or
24 dB/octave Linkwitz-Riley
Filter Modes: Low-Pass or High-Pass, Defeatable.
Cutoff Freq. Range: Continuously variable, 50 - 500 Hz
Input Sections:
No. of Inputs: Two Stereo Pairs (Front and Rear)
Input Type: Differential-balanced with RCA jack inputs
Input Range: Switchable from 200mV - 2V RMS (Low)
to 800mV - 8V RMS (High)
Preamp Output:
2-Channel, buffered pass-through type, switch-selectable
to pass signal from “Front” inputs only, or from all four
inputs (summed).
Chassis Dimensions (LxWxH):
10.74 in. x 7.85 in. x 1.93 in. (273 mm x 199.5 mm x 49 mm)
Dimensions do not include connectors.
Due to ongoing product development, all specifications are subject to
change without notice.
18 | JL Audio - HD600/4 Owners Manual
19
The Nine-Step Procedure
(follow this procedure for each pair of channels)
1) Disconnect the Speaker Connector Plugs.
2) Turn off all processing on the source unit
(bass/treble, loudness, EQ, etc.). Set fader
control to center position and subwoofer
level control to 3/4 of maximum (if
used to drive the HD600/4). Disconnect
the HD-RLC Remote Level Control
temporarily (if one is being used).
3) Switch the “Input Voltage” to “Low” and
turn the “Input Sens.” control on both sets of
channels all the way down.
4) Set the source unit volume to 3/4 of full
volume. If either set of channels is being
driven by a source units dedicated subwoofer
output, also adjust the source unit’s subwoofer
level control to 3/4 of maximum output. This
will allow for reasonable gain overlap with
moderate clipping at full volume.
5) Using the chart below, determine the
target voltage for input sensitivity
adjustment according to the nominal
impedance of the speaker system
connected to each set of outputs.
6) Verify that you have disconnected the Speaker
Connector Plugs before proceeding. Play a
track with an appropriate sine wave (within the
frequency range to be amplified by each set of
channels) at 3/4 source unit volume.
7) Connect the AC voltmeter to the “Front
Speaker Outputs” or “Rear Speaker Outputs
connectors of the amplifier. If the channel pair
is operating in stereo, it is only necessary to
measure one channel in the pair. If bridged,
make sure you test the voltage at the correct
connectors (L+ and R–).
8) Increase the “Input Sens.” control until
the target voltage is delivered for that set
of channels. If excessive voltage is read
on either set of channels with the control
at minimum (full counterclockwise),
switch the appropriate “Input Voltage
switch to “High” and re-adjust.
9) Once you have adjusted each set of channels to
its maximum unclipped output level, reconnect
the speaker(s). The “Input Sens.” controls can
now be adjusted downward if either or both
sets of channels requires attenuation to achieve
the desired system balance.
Nom.
Impedance
FRONT CHANNELS REAR CHANNELS
Stereo Bridged Stereo Bridged
8 24.5 V 49.0 V 24.5 V 49.0 V
6 24.5 V 42.4 V 24.5 V 42.4 V
4 24.5 V 34.6 V 24.5 V 34.6 V
3 21.2 V 30.0 V 21.2 V 30.0 V
2 17.3 V
not recommended
17.3 V
not recommended
1.5 15.0 V
not recommended
15.0 V
not recommended
APPENDIX B:
Precise Frequency Selection Chart
“FILTER FREQ”
Detent Panel Actual
Number Marking Freq.
Full counter-clockwise: 53
01 ...........“50” ............53
02 ............................53
03 ............................53
04 ............................53
05 ............................54
06 ............................56
07 ............................58
08 ...........“60” ............60
09 ............................62
10 ............................64
11 ............................66
12 ............................68
13 ............................71
14 ............................74
15 ............................76
16 ...........“80” ............80
17 ............................83
18 ............................87
19 ............................91
20 .............. ..............94
21 ............................99
22 ...........................104
23 ...........................109
24 .......“12 oclock .......115
25 ...........................121
26 ...........................128
27 ...........................137
28 ...........................147
29 ...........................160
30 ...........................174
31 ...........................191
32 ...........................211
33 ..........“250” ..........236
34 ...........................269
35 ...........................309
36 ...........................369
37 ...........................443
38 ..........“500” ..........484
39 ...........................525
Full-clockwise: 528
APPENDIX C:
Input Sensitivity Level Setting
JL Audio amplifiers utilizing the Regulated
Intelligent Power Supply (R.I.P.S.) allow
delivery of their rated power when connected
to any load impedance from 1.5 - 4Ω per
channel and when connected to a charging
system with any voltage from 11 - 14.5V.
This design is beneficial for many reasons.
One of these reasons is ease of setup.
Because each JL Audio amplifier will
always deliver the same amount of power
within its operational range of impedances
and supply voltages, the maximum,
unclipped output is very predictable.
This makes setting the gain structure via the
input sensitivity controls very simple. Following
the directions below will allow the user to adjust
the input sensitivity of the amplifier(s) simply
and easily in just a few minutes using equipment
which is commonly available in installation bays.
Necessary Equipment
• Digital AC Voltmeter
CD with a sine-wave test tone recorded at
0 dB reference level in the frequency range
to be amplified for that set of channels
(50 Hz for subwoofer channels, 1 kHz for
a midrange application). The CleanSweep®
Calibration Disc contains the appropriate
test tones and is available for sale at
http://store.jlaudio.com Do not use attenuated
test tones (-10 dB, -20 dB, etc.).
Do not increase any “Input Sens.” setting in
the system beyond the maximum level
established during this procedure. Doing so
will result in audible distortion and possible
speaker damage.
It will be necessary to re-adjust the “Input
Sens.for the affected channels if any equalizer
boost is activated after setting the Input
Sens.” with this procedure. This applies to any
EQ boost circuit, source unit tone controls or EQ
circuits. EQ cuts will not require re-adjustment.
20 | JL Audio - HD600/4 Owners Manual
21
“My amplifier shuts off once in a while, usually at higher volumes”
Check your voltage source and grounding point. The power supply
of the HD600/4 will operate with charging system voltages
down to 10V. Shutdown problems at higher volume levels
can occur when the charging system voltage drops below
10V. These dips can be of very short duration making them
extremely difficult to detect with a common DC voltmeter.
To ensure proper voltage, inspect all wiring and termination
points. It may also be necessary to upgrade the ground
wire connecting the battery to the vehicles chassis and the
power wire connecting the alternator to the battery. Many
vehicles employ small (10 AWG - 6 AWG) wire to ground the
battery to the vehicles chassis and to connect the alternator to
the battery. To prevent voltage drops, these wires should be
upgraded to 4 AWG when installing amplifier systems with
main fuse ratings above 60A. Grounding problems are the
leading cause of misdiagnosed amplifier “failures.”
“My amplifier turns on, but there is no output
Check the input signal using an AC voltmeter to measure the
voltage from the source unit while an appropriate test tone is
played through the source unit (disconnect the input cables
from the amplifier prior to this test). The frequency used
should be in the range that is to be amplified by the amplifier
(example: 50 Hz for a sub bass application or 1 kHz for a full
range / high-pass application). A steady, sufficient voltage
(between 200mV and 8.0-volts) should be present at the
output of the signal cables.
Check the output of the amplifier. Using the procedure explained
in the previous check item (after plugging the input cables
back into the amplifier) test for output at the speaker outputs
of the amplifier. Unless you enjoy test tones at high levels,
it is a good idea to remove the Speaker Connector Plugs
from the amplifier while doing this. Turn the volume up
approximately half way. 5V or more should be measured
at the speaker outputs. This output level can vary greatly
between amplifiers but it should not be in the millivolt
range with the source unit at half volume. If you are reading
sufficient voltage, check your speaker connections as
explained below.
Check to ensure that the speaker wires are making a good
connection with the metal inside the Speaker Connector
Plugs. The speaker wire connectors are designed to accept up
to 12 AWG wire. Make sure to strip the wire to allow for a
sufficient connection with the metal inside each terminal.
“How do I properly set the input sensitivity on my amplifier
Please refer to Appendix C (pages 18, 19) to set the input sensitivity
for maximum, low-distortion output.
“My amplifier doesn’t turn on”
Check the fuse(s), not just visually, but with a continuity meter. It
is possible for a fuse to have poor internal connections that
cannot be found by visual inspection. It is best to take the
fuse out of the holder for testing. If no problem is found with
the fuse, inspect the fuse-holder.
Check the integrity of the connections made to each of the
+12VDC, “Ground, andRemote” terminals. Ensure
that no wire insulation is pinched by the terminal set screw
and that each connection is tight.
Check to make sure there is +12V at the “Remote” connection of the
amplifier. In some cases, the turn-on lead from the source unit
is insufficient to turn on multiple devices and the use of a relay
is required. To test for this problem, jump the +12VDC wire
to the Remote terminal to see if the amplifier turns on.
“I get a distorted / attenuated sound coming out of the speaker(s)”
Check the speaker wires for a possible short, either between the
positive and negative leads or between either speaker lead
and the vehicles chassis ground. If a short is present, you
will experience distorted and/or attenuated output. The
“Status” LED will turn amber (yellow) in this situation. It
may be helpful to disconnect the speaker wires from the
amplifier and use a different set of wires connected to a test
speaker.
Check the nominal load impedance to verify that each channel
of the amplifier is driving a load equal to or greater than
1.5 ohms in stereo mode (3 ohms bridged).
Check the input signal and input signal cables to make sure signal
is present at the Amplifier Inputs” and the cables are not
pinched or loose. It may be helpful to try a different set of
cables and/or a different signal source to be sure.
“My amplifier’s output fluctuates when I tap on it or hit a bump
Check the connections to the amplifier. Make sure that the
insulation for all wires has been stripped back far enough to
allow a good contact area inside the connector plugs.
Check the input connectors to ensure that they all are making good
contact with the input jacks on the amplifier.
APPENDIX D: TROUBLESHOOTING
22 | JL Audio - HD600/4 Owners Manual
23
INSTALLATION NOTES:
Use this diagram to document your amplifier’s switch and control positions.
LIMITED WARRANTY  AMPLIFIERS USA
JL AUDIO warrants this product to be free of defects in materials and workmanship for a period of two
(2) years. The warranty is extended to three (3) years total if installation is performed by an authorized
JL Audio dealer using a JL Audio Premium Power Connection System for power wiring.
This warranty is not transferable and applies only to the original purchaser from an authorized
JL AUDIO dealer. Should service be necessary under this warranty for any reason due to manufacturing
defect or malfunction, JL AUDIO will (at its discretion), repair or replace the defective product with new
or remanufactured product at no charge. Damage caused by the following is not covered under warranty:
accident, misuse, abuse, product modification or neglect, failure to follow installation instructions,
unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental
or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic
damage due to accident or normal wear and tear is not covered under warranty.
Warranty is void if the product’s serial number has been removed or defaced.
Any applicable implied warranties are limited in duration to the period of the express warranty as
provided herein beginning with the date of the original purchase at retail, and no warranties, whether
express or implied, shall apply to this product thereafter. Some states do not allow limitations on implied
warranties, therefore these exclusions may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.
If you need service on your JL AUDIO product:
All warranty returns should be sent to JL AUDIO ’s Amplifier Service Facility freight-prepaid through
an authorized JL AUDIO dealer and must be accompanied by proof of purchase (a copy of the original
sales receipt). Direct returns from consumers or non-authorized dealers will be refused unless specifically
authorized by JL AUDIO with a valid return authorization number.
Warranty expiration on products returned without proof of purchase will be determined from the
manufacturing date code. Coverage may be invalidated as this date is previous to purchase date. Non-
defective items received will be returned freight-collect. Customer is responsible for shipping charges and
insurance in sending the product to JL AUDIO. Freight damage on returns is not covered under warranty.
For Service Information in the U.S.A. please call
JL Audio Customer Service: (954) 443-1100
9:00 AM – 5:30 PM (Eastern Time Zone)
JL Audio, Inc
10369 North Commerce Pkwy.
Miramar, FL 33025
(do not send product for repair to this address)
International Warranties:
Products purchased outside the United States of America are covered only
by that country’s distributor and not by JL Audio, Inc.
Single-Cycle Control™ (U.S. Patent #6,084,450) is used under exclusive license for mobile audio from Power Physics, Inc. - Newport Beach, CA
Printed in China
HD600/4MAN-CH-040912
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio 4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio 4 in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info