700463
12
Zoom out
Zoom in
Previous page
1/16
Next page
12 | JL Audio - XD200/2v2 Owners Manual
APPENDIX A:
Input Sensitivity Level Setting
Following the directions below will allow the
installer to adjust the input sensitivity of each
amplifier channel pair simply and easily in just a
few minutes using equipment which is commonly
available in installation bays.
Necessary Equipment
• Digital AC Voltmeter
CD with a sine-wave test tone recorded at
0 dB reference level in the frequency range
to be amplified for that set of channels
(50 Hz for subwoofer channels, 1 kHz for a
midrange application). Do not use attenuated
test tones (-10 dB, -20 dB, etc.).
The Nine-Step Procedure
1) Disconnect the speaker(s) from the
amplifier’s speaker output connectors.
2) Turn off all processing (bass/treble, loudness,
EQ, etc.) on the source unit, processors (if used)
and amplifier. Set the fader control to center
position and the subwoofer level control to 3/4
of maximum (if used to feed the XD200/v2).
3) Switch the “Input Voltage” switch to “Low
and turn all three “Input Sens.” controls all the
way down.
4) Set the source unit volume to 3/4 of full
volume. This will allow for reasonable gain
overlap with moderate clipping at full volume.
5) Using the chart on this page, determine the target
voltage for input sensitivity adjustment according
to the nominal impedance of the speaker system
connected to the amplifier outputs.
6) Verify that you have disconnected the speakers
before proceeding. Play a track with an
appropriate sine wave (within the frequency
range to be amplified by the XD200/2v2) at 3/4
source unit volume.
7) Connect the AC voltmeter to the speaker
output connectors of the amplifier. Make sure
you test the voltage at the correct connectors
(+ and –).
8) Increase the Input Sens.” control until the
target voltage is observed with the voltmeter.
9) Once you have adjusted each channel
section on the XD200/2v2 to its maximum
low-distortion output level, reconnect
the speaker(s). The “Input Sens.
controls can now be adjusted downward
if the amplifier requires attenuation to
achieve the desired system balance.
Do not increase any “Input Sens.” setting for
any amplifier channel or channel pair in the
system beyond the maximum level established
during this procedure. Doing so will result in
audible distortion and possible speaker damage.
It will be necessary to re-adjust the “Input
Sens.” if any equalizer boost is activated after
setting the “Input Sens.” with this procedure.
This applies to any EQ boost circuit, including
source unit tone controls or EQ circuits. EQ cuts
will not require re-adjustment
Nom.
Impedance
Target AC Voltage
Stereo Bridged
8
17.3 V 34.6 V
4
17.3 V 28.2 V
2
14.1 V not recommended
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio 2v2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio 2v2 in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info