700446
4
Zoom out
Zoom in
Previous page
1/13
Next page
6 | JL Audio - 1200/1v3 Owners Manual
7
AMPLIFIER INPUT SECTION
The 1200/1v3 employs a differential-balanced
input topology that provides the user with a high
degree of input flexibility while retaining superior
noise rejection. This type of circuit also allows
the 1200/1v3 to accept high-voltage inputs from
factory source unit outputs without excessive
distortion or noise problems.
+12VDC Ground Remote Preamp Output Section Infrasonic Filter “Q” Center Freq. Boost (dB) Amp LP Filter
Advanced
Bass
Control
Amplifier Input Section
Subwoofer Output
MONO OUTPUT ONLY
Left Output Right Output
Left Ch. Right Ch.
Filter Freq. (Hz) Filter Freq. (Hz)Infrasonic Freq. (Hz) Remote Bass Port
Full Range
|
Amp Filter
|
Out Filter
Output Mode Filter Slope Mode Mode
|
Slope
Input Voltage Input Sens.
Output Polarity
12dB
|
24dB
Filter Mode
LP
|
HP
Bass EQ
Off
|
On
Off
|
12dB
|
24dB
Low
|
High
Normal
|
Reversed
Off
|
On
40
45
55
65
85
120
200 15
18
25
30
40
50
60 40
45
55
65
80
100
200
0.5
0.7
1.1
1.6
2.7
4.3
20
25
35
45
55
70
80 0
+4
+10
+13
+15
120 0 /1v3
Monoblock Subwoofer Amplifier
1) Input Connections: A standard left/right pair
of RCA type jacks is used for input on
the 1200/1v3. You may run a stereo or a mono
signal into the inputs of the amplifier. The
amplifier’s input section automatically sums
stereo signals to mono for the internal
amplifier section and for the “LPFilter
Mode” of the Preamp Output” section.
IMPORTANT
!
If you plan to use the “Preamp Output” in
“Full-Range” or “HP” mode to feed a stereo
amplifier, you must connect a stereo signal to
the input of the amplifier. A mono signal into
the amplifier will result in a mono signal out of
the preamp output. (Its a great amplifier, but it
doesn’t do magic).
The amplifier will operate with only one input
connection (left or right), but will require an
increase in input sensitivity to overcome the loss
of signal. If a mono input signal is to be run, we
recommend that you use a “Y-adaptor” like the
JLAudio ECS model XD-CLRAICY-1F2M to split
the mono signal into both inputs of the amplifier.
2) Input Voltage Range: A wide range of signal
input voltages can be accommodated by
the 1200/1v3’s input section (200mV – 8V).
This wide range is split up into two sub-
ranges, accessible via switches located in the
Amplifier Input Section” of the amplifier.
The “Low” position on the “Input Voltage
switch selects an input sensitivity range
between 200mV and 2V. This means that
the “Input Sens.” rotary control will operate
within that voltage window. If you are using
an aftermarket source unit, with conventional
preamp-level outputs, this is most likely the
position that you will use. The High” position
on the “Input Voltageswitch selects an input
sensitivity range between 800mV and 8V. This
is useful for certain high-output preamp level
signals as well as speaker-level output from
source units and small amplifiers. To use
speaker-level sources, splice the speaker output
wires of the source unit or small amplifier
onto a pair of RCA cables or plugs or use the
JLAudio ECS Speaker Wire to RCA adaptor
(XD-CLRAIC2-SW).
Ground Connection
The chassis ground connection must be made
using 4 AWG pure copper wire and should
be kept as short as possible, while accessing a
solid piece of sheet metal in the vehicle. The
surface of the sheet metal should be sanded at
the contact point to create a clean, metal-to-
metal connection between the chassis and the
termination of the ground wire with a brass or
copper power ring. For optimal grounding, we
recommend the use of a JLAudio master ground
lug (XB-MGLU). Alternatively, a sheet metal
screw or bolt can be used with a star washer.
IMPORTANT
!
Many vehicles employ small (10 AWG - 6 AWG)
wire to ground the battery to the vehicle chassis
and to connect the alternators positive
connection to the battery. To prevent voltage
drops, these wires should be upgraded to 4
AWG pure copper wire (or larger) when
installing amplifier systems with main fuse
ratings above 60A.
REMOTE TURNON
The 1200/1v3 uses a conventional +12V remote
turn-on lead, typically controlled by the source
unit's remote turn-on output. The amplifier will
turn on when +12V is present at its “Remote”
input and turn off when +12V is switched off. If
a source unit does not have a dedicated remote
turn-on output, the amplifier’s turn-on lead can
be connected to +12V via a switch that derives
power from an ignition-switched circuit.
The 1200/1v3's “Remote” turn-on connector is
designed to accept 12 AWG – 8 AWG wire.
12 AWG is more than adequate for this purpose.
To connect the remote turn-on wire to the
amplifier, first back out the set screw on the
top of the amplifier, using the supplied hex
wrench. Strip 1/2 inch (12mm) of wire and
insert the bare wire into the receptacle on the
front panel of the amplifier, seating it firmly so
that no bare wire is exposed. Smaller wire than
12 AWG can be used, but it may be necessary
to strip 1 inch of insulation from the wire and
fold the bare wire in half prior to insertion.
While holding the wire in the terminal, tighten
the set screw firmly, taking care not to strip
the head of the screw and making sure that
the wire is firmly gripped by the set screw.
+12VDC Ground Remote
Preamp Output Section Infrasonic Filter “Q” Center Freq. Boost (dB) Amp LP Filter
Advanced
Bass
Control
Amplifier Input Section Subwoofer Output
MONO OUTPUT ONLY
Left Output Right Output Left Ch. Right Ch.Filter Freq. (Hz) Filter Freq. (Hz)Infrasonic Freq. (Hz) Remote Bass Port
Full Range
|
Amp Filter
|
Out Filter
Output Mode Filter Slope Mode Mode
|
Slope Input Voltage Input Sens.
Output Polarity
12dB
|
24dB
Filter Mode
LP
|
HP
Bass EQ
Off
|
On
Off
|
12dB
|
24dB Low
|
High
Normal
|
Reversed
Off
|
On
40
45
55
65
85
120
200 15
18
25
30
40
50
60 40
45
55
65
80
100
200
0.5
0.7
1.1
1.6
2.7
4.3
20
25
35
45
55
70
80 0
+4
+10
+13
+15
120 0 /1v3
Monoblock Subwoofer Amplifier
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio 1v3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio 1v3 in the language / languages: English as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info