700451

JL Audio 1v2 Manual

7
Zoom out
Zoom in
Previous page
1/41
Next page
12 | JL Audio - XD1200/1v2 Owner’s Manual
13
ENGLISH
APPENDIX B:
Precise Frequency Selection Chart
“FILTER FREQ” AMP FILTER
Detent Panel Actual
Number Marking Freq.
Full counter-clockwise: 53
01 ............................53
02 ...........“50” ............53
03 ............................54
04 ............................54
05 ............................55
06 ............................57
07 ............................59
08 ...........“60” ............61
09 ............................63
10 ............................65
11 ............................67
12 ............................70
13 ............................72
14 ............................75
15 ............................78
16 ...........“80” ............81
17 ............................85
18 ............................88
19 ............................93
20 .......“12 o’clock” ........97
21 ...........................102
22 ...........................107
23 ...........................113
24 ..........“120” ..........120
25 ...........................127
26 ...........................135
27 ...........................144
28 ...........................156
29 ...........................169
30 ...........................184
31 ...........................203
32 ..........“200” ..........227
33 ...........................254
34 ...........................290
35 ...........................337
36 ...........................392
37 ...........................426
38 ..........“500” ..........447
39 ...........................467
Full-clockwise: 470
APPENDIX C:
XD1000/1v2 Specifications
General Specifications:
Recommended Fuse Value: 80A
Recommended Fuse Type: MAXI® or AGU
Input Sections:
No. of Inputs: One Stereo Pair
Input Type: Differential-balanced with RCA jack inputs
Input Range: 200mV - 8V RMS
Amplifier Section:
Amplifier Topology: NexD™ High Speed Class D
Power Supply: Unregulated MOSFET switching type
Rated Power at 14.4V with less than
1% THD+Noise (20Hz - 20 kHz)
600W RMS x 1 @ 4 ohms
800W RMS x 1 @ 3 ohms
1000W RMS x 1 @ 2 ohms
Rated Power @ 12.5V with less than
1% THD + Noise (20Hz - 20 kHz)
500W RMS x 1 @ 4 ohms
650W RMS x 1 @ 3 ohms
800W RMS x 1 @ 2 ohms
Signal to Noise Ratio:
>83 dB referred to rated power
(A-weighted, 20 Hz-20 kHz noise bandwidth)
>53 dB referred to 1W
(A-weighted, 20 Hz-20 kHz noise bandwidth)
Frequency Response: 7 Hz - 500 Hz (+0, -1dB)
Damping Factor:
>1000 @ 4 ohms / 50 Hz
>500 @ 2 ohms / 50 Hz
Amplifier Filters:
Amplifier Low-Pass Filter:
State-variable, 12 dB/octave Butterworth or 24 dB/octave
Linkwitz-Riley with continuously variable cutoff frequency
selection from 50 - 500 Hz (defeatable).
Infrasonic Filter:
24 dB/octave Butterworth @ 30 Hz (defeatable).
Preamp Output:
Buffered pass-through type.
Dimensions(LxWxH):
14.73” x 7.09” x 2.05” (374mm x 180mm x 52mm)
APPENDIX A:
Input Sensitivity Level Setting
Following the directions below will allow the
installer to adjust the input sensitivity of each
amplifier channel pair simply and easily in just a
few minutes using equipment which is commonly
available in installation bays.
Necessary Equipment
• Digital AC Voltmeter
• CD with a sine-wave test tone recorded at
0 dB reference level in the frequency range
to be amplified for that set of channels
(50 Hz for subwoofer channels, 1 kHz for a
midrange application). Do not use attenuated
test tones (-10 dB, -20 dB, etc.).
The Nine-Step Procedure
1) Disconnect the speaker(s) from the
amplifier’s speaker output connectors.
2) Turn off all processing (bass/treble, loudness,
EQ, etc.) on the source unit, processors (if
used) and amplifier. Set fader control to center
position and subwoofer level control to 3/4 of
maximum (if used to feed the XD1000/1v2).
3) Turn the amplifier’s “Input Sens.” control all
the way down.
4) Set the source unit volume to 3/4 of full
volume. This will allow for reasonable gain
overlap with moderate clipping at full volume.
5) Using the chart on this page, determine the target
voltage for input sensitivity adjustment according
to the nominal impedance of the speaker system
connected to the amplifier outputs.
6) Verify that you have disconnected the speakers
before proceeding. Play a track with an
appropriate sine wave (within the frequency
range to be amplified by the XD1000/1v2) at
3/4 source unit volume.
7) Connect the AC voltmeter to the speaker output
connectors of the amplifier. Make sure you test
the voltage at the correct connectors (+ and –).
8) Increase the “Input Sens.” control until the
target voltage is observed with the voltmeter.
9) Once you have adjusted the XD1000/1v2 to
its maximum low-distortion output level,
reconnect the speaker(s). The “Input Sens.”
controls can now be adjusted downward if the
amplifier requires attenuation to achieve the
desired system balance.
Do not increase any “Input Sens.” setting for
any amplifier channel or channel pair in the
system beyond the maximum level established
during this procedure. Doing so will result in
audible distortion and possible speaker damage.
It will be necessary to re-adjust the
“Input Sens.” if any equalizer boost is activated
after setting the “Input Sens.” with this
procedure. This applies to any EQ boost circuit,
including source unit tone controls or EQ
circuits. EQ cuts will not require re-adjustment.
Nom. Impedance Target AC Voltage
4 63.2 V
3 49.0 V
2 34.6 V
1
Not Recommended
Due to ongoing product development, all specifications are subject to
change without notice.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio 1v2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio 1v2 in the language / languages: English as an attachment in your email.

The manual is 4,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info