700471
6
Zoom out
Zoom in
Previous page
1/37
Next page
10 JL Audio JX250/1 • JX500/1D • JX1000/1D 11
ENGLISH
STATUS INDICATOR LIGHTS /
PROTECTION CIRCUITRY
There are two status indicator lights on the
amplifier’s control panel. These are as follows:
1) Power (Green): Located at the far left of the
amplifier’s control panel, this LED lights to
indicate that the amplifier is turned on and
operating normally.
2) Protect (Red): Indicates that the amplifier
protection circuitry has been activated
to prevent product failure due to thermal
overload, short-circuit or a dangerously
low impedance connected to the amplifier
outputs. Connecting the speaker output to
an impedance lower than 2 ohms will cause
this protection mode to activate. When this
protection mode is activated, the amplifier will
shut down to protect its circuitry. When the
problem is corrected, the amplifier will return
to normal operation and the “Protect LED
will shut off.
SERVICING YOUR AMPLIFIER
If your amplifier fails or malfunctions, please
return it to your authorized JL Audio dealer so
that it may be sent in to JL Audio for service.
There are no user serviceable parts or fuses inside
the amplifier. The unique nature of the circuitry
in the JL Audio amplifiers requires specifically
trained service personnel. Do not attempt
to service the amplifier yourself or through
unauthorized repair facilities. This will not only
void the warranty, but may result in the creation
of more problems within the amplifier.
If you have any questions about the installation or
setup of the amplifier not covered in this manual,
please contact your dealer or technical support.
JL Audio Technical Support:
(954) 443-1100
9:00 AM – 5:30 PM (Eastern Time Zone)
Monday - Friday
SPEAKER OUTPUT
Subwoofer connection to the JX monoblock
is straightforward and takes place at the
far right of the power/speaker connection
panel. Two positive (“+”) connections and
two negative (“”) connections are available
via a connector labeled Speaker Output
(Mono)”. The dual connections allow for two
separate speaker wire runs to be parallel-
connected to the amplifiers mono output.
IMPORTANT!
!
Speaker loads below 2Ω nominal are not
recommended and will cause the amplifier to
enter into a protection mode.
Do not chassis ground any speakers connected
to this or any other JL Audio amplifier. Doing so
will cause the amplifier to go into protection.
To connect the speaker wires to the amplifier,
strip 1/2-inch (12 mm) of insulation from each
speaker wire and insert them into their
appropriate connector (observing correct
polarity). Then, tighten each connector using the
supplied 2.5 mm hex wrench.
IMPORTANT!
!
Do NOT attempt to “bridge” two JX
monoblocks together or combine their output
to a single load in any manner. Doing so will
damage the amplifier(s).
IMPORTANT!
!
Before reconnecting the battery ground and
turning the system on, verify that all control
settings on the amplifier are set according to
the needs of the system.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio 1D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio 1D in the language / languages: English as an attachment in your email.

The manual is 2,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info