701353
6
Zoom out
Zoom in
Previous page
1/16
Next page
Infrasonic Filter:
Turn “O” for Sealed Enclosure.
Turn “On” for Ported Enclosure and
set the knob to “25” Hz.
Bass EQ:
Generally not necessary in W7 applications (we recommend defeating it by
switching the “Bass EQ” switch to “O”). May be used with Remote Bass
Control to provide some user controllable broad bass boost. When used in this
manner, setQ” to “1.1”, setCenter Freq.to “45” Hz, “Boostis defeated by
connection of Remote Bass Control.
Input Sensitivity Controls:
Proper adjustment of these controls is critical!
For virtually all aftermarket head units,
set “Input Voltage” to “Low.
See “Input Sensitivity Setting Guide”
on pg. 14 for precise setting instructions.
Dual Mono Speaker
Output Connections:
Connect wire directly to “+”
and “–” “Subwoofer Output
connections and to the W7.
Remote Bass Port:
Permits connection of an
optional remote bass boost
controller (RBC-1), giving you
control over the boost of the
parametric EQ from the front
of the vehicle. The RBC-1
controller is sold separately.
Amp Low-Pass Filter:
SetMode/Slopeswitch to “24dB”.
Set “Filter Freq. (Hz)” knob to “85”.
Lower settings are likely to result in a
poor transition between the upper
response of the W7 and the lower
response of the mid-bass speakers.
Amplier Input:
Connect RCA-type
cables from the head
unit (or processor) to
these two jacks.
Use both jacks
(with a Y-adapter
if necessary).
Output Polarity:
Carefully listen to the sub-bass to
mid-bass transition with music that
has strong mid-bass content. Select
the switch position which gives the
smoothest, most natural mid-bass
response. If using multiple 1000/1’s
on multiple subwoofers, make sure
this switch is set to the same position
on all ampliers.
JL Audio 1000/1v2:
These settings are intended
as a “baseline” for tuning
your system. Depending
on your vehicle and your
preferences, some variation in
the crossover and bass control
settings may be necessary
for optimum performance.
RECOMMENDED CONTINUOUS RMS POWER RANGE FOR ONE SUBWOOFER DRIVER:
750W 1000W 1500W 2000W 4000W500W
= position of knob
= position of switch
= switch with two possible positions
= setting will vary (see sidebar)
Amplifier Recommendation: 1000/1v2
13W7-D1.5
Free Air Resonance (Fs): 23.5 Hz
Electrical “Q” (Qes): 0.476
Mechanical “Q” (Qms): 7.517
Total Speaker “Q” (Qts): 0.448
Equivalent Compliance (Vas): 3.68 cu. ft. (104.3 ltrs)
One-Way, Linear Excursion (Xmax)*: 1.25 in. (32 mm)
Thermal Power Handling (Pt): 1500 Watts Continuous
Reference Efficiency (no): 0.269 %
Efficiency (SPL @ 1W/1m): 86.3 dB
DC Resistance (Re): 2.41Ω
Effective Piston Area (Sd): 107.35 sq. in. (0.0693 sq. m)
Nominal Impedance (Znom): Dual 1.5Ω
* Xmax specifications are derived via one-way voice coil overhang
method with no correction factors applied.
** For parallel-wired voice coils, divide “Re” by 4.
All other specifications remain the same.
6
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio 10W7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio 10W7 in the language / languages: English as an attachment in your email.

The manual is 2,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info