701264
2
Zoom out
Zoom in
Previous page
1/4
Next page
2 JL AUDIO 10W6v3-D4
SUBWOOFER 10W6v3-D4
Free Air Resonance (Fs): 30.12 Hz
Electrical “Q” (Qes): 0.543
Mechanical “Q” (Qms): 9.228
Total Speaker “Q” (Qts): 0.513
Equivalent Compliance (Vas):
0.821 ft
3
23.25 liters
One-way, Linear Excursion
(Xmax)*:
0.75 in
19 mm
Efficiency (1W/1m)**: 82.7 dB SPL
Effective Piston Area (Sd):
49.303 in
2
0.0318 m
2
DC Resistance (Re)***: 6.452 ohm
Nominal Impedance:
Dual 4-ohm
voice coils
Power Handling (continuous): 600 W
A
B
E
D
C
10W6v3 SUBWOOFER
PHYSICAL SPECIFICATIONS
Nominal Diameter:
10.0 in
250 mm
Overall Diameter (A):
10.5 in
267 mm
Mounting Hole Diameter (B):
9.02 in
229 mm
Bolt Hole Circle (C):
9.86 in
250 mm
Magnet Diameter (D):
6.3 in
160 mm
Mounting Depth (E):
6.89 in
175 mm
Required Pole-Vent Clearance:
0.50 in
12.5 mm
Net Weight:
20 lbs
9.1 kg
Driver Displacement:
0.078 ft
3
2.21 liters
JL AUDIO 10W6v3-D4
U.S. PATENTS: 6,535,613 #6,118,884 #6,219,431 #6,229,902 #6,501,844 • Other U.S. & Foreign Patents Pending
W6v3 Terminal Jumper System
Please note that the W6v3 is a dual voice coil driver.
BOTH voice coils must be connected to the amplifier
(in series or parallel) for the speaker to operate
properly. To accomplish this, each W6v3 features a
pair of main input connection push-terminals and
four voice coil configuration tab terminals. These are
located behind the main input connectors and are
used to interconnect the dual voice coils in one of
two ways: Diagram A shows a series connection
(8Ω nominal impedance per speaker). Diagram B
shows a parallel connection (2Ω nominal impedance
per speaker) and is the way the speaker is configured
at the factory. After verifying that the tabs are
properly configured using the supplied jumper(s),
connect the amplifier’s output wires to the W6v3s
main input push-terminals and install the speaker
into the enclosure.
All specifications are subject to change without notice.
Diagram A: Series Connection (8Ω):
Use one jumper from “VC1–” to “VC2+
Warning! Failure to properly connect the
configuration tabs will result in no output and
may damage the speaker.
Diagram B: Parallel Connection (2Ω):
Use two jumpers... one from “VC1–” to “VC2–” and
one from “VC1+ to “VC2+”.
* Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.
** Efficiency (1W/1m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to
other subwoofers to determine which one is “louder” !
*** Re (DC resistance) is measured with the voice coils in series, for parallel-wired specification divide Re by 4. All other
specifications remain the same.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio 10W6v3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio 10W6v3 in the language / languages: English as an attachment in your email.

The manual is 0,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info