700439

JL Audio 1 Manual

10
Zoom out
Zoom in
Previous page
1/13
Next page
18 | JL Audio - HD1200/1 Owner’s Manual
19
The Nine-Step Procedure
1) Disconnect the Speaker Connector Plug.
2) Turn off all processing on the source unit
(bass/treble, loudness, EQ, etc.). Set fader
control to center position and subwoofer
level control to 3/4 of maximum (if used
to drive the HD1200/1). Disconnect
the HD-RLC Remote Level Control
temporarily (if one is being used).
3) Switch the “Input Voltage” to “Low” and turn
the “Input Sens.” control all the way down.
4) Set the source unit volume to 3/4 of full
volume. If the amplifier is being driven by a
source unit’s dedicated subwoofer output, also
adjust the source unit’s subwoofer level control
to 3/4 of maximum output. This will allow for
reasonable gain overlap with moderate clipping
at full volume.
5) Using the chart below, determine the
target voltage for input sensitivity
adjustment according to the nominal
impedance of the speaker system
connected to each set of outputs.
Nom.
Impedance
HD 1200/1
MONO
8 69.3 V
6 69.3 V
4 69.3 V
3 60.0 V
2 49.0 V
1.5 42.4 V
6) Verify that you have disconnected the Speaker
Connector Plug before proceeding. Play a
track with an appropriate sine wave (within
the frequency range to be amplified by each
set of channels) at 3/4 source unit volume.
7) Connect the AC voltmeter to the Speaker
Output contacts of the amplifier.
8) Increase the “Input Sens.” control until the
target voltage is delivered. If excessive voltage
is read with the control at minimum (full
counterclockwise), switch the “Input Voltage”
switch to “High” and re-adjust.
9) Once you have adjusted the amplifier to its
maximum unclipped output level, reconnect
the speaker(s). The “Input Sens.” controls can
now be adjusted downward if the HD1200/1
requires attenuation to achieve the desired
system balance.
APPENDIX B:
Precise Frequency Selection Chart
“FILTER FREQ”
Detent Panel Actual
Number Marking Freq.
Full counter-clockwise: 53
01 ...........“50” ............53
02 ............................53
03 ............................53
04 ............................53
05 ............................54
06 ............................56
07 ............................58
08 ...........“60” ............60
09 ............................62
10 ............................64
11 ............................66
12 ............................68
13 ............................71
14 ............................74
15 ............................76
16 ...........“80” ............80
17 ............................83
18 ............................87
19 ............................91
20 .............. ..............94
21 ............................99
22 ...........................104
23 ...........................109
24 .......“12 o’clock” .......115
25 ...........................121
26 ...........................128
27 ...........................137
28 ...........................147
29 ...........................160
30 ...........................174
31 ...........................191
32 ...........................211
33 ..........“250” ..........236
34 ...........................269
35 ...........................309
36 ...........................369
37 ...........................443
38 ..........“500” ..........484
39 ...........................525
Full-clockwise: 528
APPENDIX C:
Input Sensitivity Level Setting
JL Audio amplifiers utilizing the Regulated
Intelligent Power Supply (R.I.P.S.) allow
delivery of their rated power when connected
to any load impedance from 1.5 - 4Ω per
channel and when connected to a charging
system with any voltage from 11 - 14.5V.
This design is beneficial for many reasons.
One of these reasons is ease of setup.
Because each JL Audio amplifier will
always deliver the same amount of power
within its operational range of impedances
and supply voltages, the maximum,
unclipped output is very predictable.
This makes setting the gain structure via the
input sensitivity controls very simple. Following
the directions below will allow the user to adjust
the input sensitivity of the amplifier(s) simply
and easily in just a few minutes using equipment
which is commonly available in installation bays.
Necessary Equipment
• Digital AC Voltmeter
• CD with a sine-wave test tone recorded at
0 dB reference level in the frequency range
to be amplified for that set of channels
(50 Hz for subwoofer channels, 1 kHz for
a midrange application). The CleanSweep®
Calibration Disc contains the appropriate
test tones and is available for sale at
http://store.jlaudio.com Do not use attenuated
test tones (-10 dB, -20 dB, etc.).
Do not increase any “Input Sens.” setting in
the system beyond the maximum level
established during this procedure. Doing so
will result in audible distortion and possible
speaker damage.
It will be necessary to re-adjust the “Input
Sens.” for the affected channels if any equalizer
boost is activated after setting the “Input
Sens.” with this procedure. This applies to any
EQ boost circuit, source unit tone controls or EQ
circuits. EQ cuts will not require re-adjustment.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio 1 in the language / languages: English as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info