686621
13
Zoom out
Zoom in
Previous page
1/15
Next page
Note: During the operation of the sand lter
pump, check the pressure reading of the
manometer.
Generally, when the pressure of the
recommended sand lter pump is less than
0.2bar (3psi) (green area) , it runs normally.
Note: You must make sure that maintenance
begins only after the sand filter pump is
unplugged. Otherwise serious risks such as
personal injury and even death may occur.
Note: Record the reading of the manometer
during the operation of the sand lt er pump.
When the manometer shows a pressure
of 0.2bar (3psi) or higher, please clean up
the sand bend or replace the sand. Use
"backwash" and "rinse" functions.
Note: regular rinsing according to use
situation is recommended.
Long-term storage and storage in winter
Using the product in a frozen pool may damage the product and invalidate the
quality warranty. If the product has to be used with antifreeze, propylene glycol
may also be used. Propylene glycol is a nontoxic chemical unharmful to any plastic
parts. Other types of antifreeze are highly toxic and may be harmful to the product’s
plastic elements.
1.Before discharging the water or repostioning of the pool, make sure the discharge
direction is towards the discharging ditch and away from the home. Review local
regulations for special water treatment requirements.
2.Switch off the product and remove the power plug.
3.After emptying, remove all connected sand filter pumps, corrugated tubes and
lter hoods on the pool wall.
4.Unscrew the drain valve (8) in an anticlockwise direction to completely empty
water inside the body. The drain plug is at the bottom of the body.
5.Dry the parts of the sand lter pump and corrugated tubes.
6.Lubricate the seal rings and washers in the order below for long-term storage.
7.The best practice for product storage is to dry the parts and motor and replace
them in the original package. To avoid shrinkage or corrosion, do not cover or wrap
the motor with a plastic bag.
8.Please store the motor and parts in a dry place at 32°F (0°C) ~104°F (40°C).
www.jilong.com SFP7-16-GB(V1)
Diagnosis of Problems and Solutions
Problems Checking Solutions
The motor can not be
started normally
Power plug not properly
inserted
Leakage protection
disconnected
Motor overheated or
overloaded
Causes motor to stop
Make sure the power cord is inserted
into the 3-core grounded metal
receptacle.
Reset circuit breaker. If the problem
persists, the power system may be
defective. Power off immediately and
confer with an expert.
Allow the motor to cool naturally and
start it again.
Filter
Unable to rinse the pool
No sand in the body
Location error of the control
valve
Excessive dirt in water
Filter barrel blocked
Sand filling Refer to sand filling
instructions
The control valve rotates to the filter
position
to prolong the running time
Clean the lter barrel
The filter is unable to
discharge water or the water
ow rate is too slow
There is blockage at the
inlet
There is an air leakage at
the gap of the inlet
Excessive dirt in water
Filter medium is blocked by
impurities
The pool is connected with
a cleaning device
Check and clear away the blockage in
the water pipes
Tighten the nozzle nuts and check the
damaged point of the nozzle and water
height
Clean the lter screen
Backwash
Disassemble the cleaning device
connected to the pool
Filter fails to run Water level is too low
Filter screen is blocked
Air leakage from the inlet
pipe
Motor or blade is blocked
Inject water to adjust water level
Clean the lter screen in the pool
Tighten the nozzle and check the
damaged point
Replace the ttings
Water leakage on the control
valve or upper cover
The seal ring of the body is
lost or too dirty
The control valve retainer
is not tightly secured
ordamaged
Remove the upper cover of the control
valve and sleeve the seal ring of the
body
Clean the seal ring of the body with a
water pipe
Tighten the screw with a screwdriver
Replace the ttings
The manometer fails to run The inner wall of the
manometer is blocked
The manometer is damaged
Remove the manometer from the
control valve and clear away the
impurities on the inner wall
Replace the ttings
Sand enters the pool The sand particles are too
ne
Use 20# quartz sand only
Particle size of the sand is 0.45-0.85mm
Or replace the sand
www.jilong.com SFP7-16-GB(V1)
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jilong 290730XX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jilong 290730XX in the language / languages: German as an attachment in your email.

The manual is 3,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jilong 290730XX

Jilong 290730XX User Manual - English - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info