509233
6
Zoom out
Zoom in
Previous page
1/48
Next page
6
If this unit is installed in a vehicle that does not have an ACC (accessory) position
on the ignition switch, the red lead of the unit should be connected to a
terminal coupled with ignition switch ON/O operations. If this is not done, the
vehicle battery may be drained when you are away from the vehicle for several
hours.
Secure the wiring with cable clamps or adhesive tape. To protect the wiring,
wrap adhesive tape around them where they lie against metal parts. To avoid
short-circuiting, cover all disconnected lead with insulating tape. There is a
possibility of short-circuiting if the leads are not insulated.
Route and secure all wiring so it cannot touch any moving parts, such as the
gear lever and handbrake. Do not route wiring in places that get hot, such as
near the heater outlet. If the insulation of the wiring melts or gets torn, there is a
danger of the wiring short-circuiting to the vehicles body.
Don’t pass the yellow lead through a hole into the engine compartment to
connect to the battery. This will damage the lead’s insulation and cause a very
dangerous short.
Do not short any leads. If you do, the protection circuit may fail to work when it
should.
Never feed power to other equipment by cutting the insulation of the power
supply lead of the unit and tapping into the lead. The current capacity of the
lead will be exceeded, causing overheating.
Since an unique audio I/C circuit is employed, never wire the unit so the
speaker leads are directly grounded or the left (-) and right (-) speaker leads are
common.
When this product’s source is switched ON, a control signal is outputted
through the blue lead. Connect to an external power amps system remote
control or the car’s Auto-antenna relay control terminal (max. 300mA 12 V DC). If
the car features a glass antenna, connect to the antenna booster power supply
terminal.
When an external power amp is being used with this system, do not connect
the blue lead to the amps power terminal. Likewise, do not connect the blue
lead to the power terminal of the auto-antenna. Such connection could cause
excessive current drain and a major malfunction. Refer to the relevant owner’s
manual for details on connecting the power amp and other units, then make
the connections correctly.
Do not block any vents or heater panels. Blocking them will cause heat to build
up and may result in re.
Make sure that the unit has a good chassis ground. A good ground connection
will eliminate most electrical noise. A good chassis ground requires a tight
connection to the vehicles metal chassis. The area around the ground
connection should be clean, bare metal without rust, paint, plastic or dirt.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jensen MP1516BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jensen MP1516BT in the language / languages: English as an attachment in your email.

The manual is 2,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info