468050

JBSystems MCD200 Manual

4
Zoom out
Zoom in
Previous page
1/43
Next page
ENGLISH USER MANUAL
JB SYSTEMS® 3/81 MCD200
In the event of serious operating problems, stop using the appliance and contact your
dealer immediately.
Please use the original packing when the device is to be transported.
Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
INSTALLATION GUIDELINES:
Install the unit in a well-ventilated location where it will not be exposed to high
temperatures or humidity.
Placing and using the unit for long periods near heat-generating sources such as
amplifiers, spotlights, etc. will affect its performance and may even damage the unit.
Take care to minimize shocks and vibrations during transport.
When installed in a booth or flight case, please make sure to have good ventilation to
improve heat evacuation of the unit.
To avoid condensation to be formed inside, allow the unit to adapt to the surrounding
temperatures when bringing it into a warm room after transport. Condense sometimes
prevents the unit from working at full performance.
CLEANING THE CD-PLAYER:
Clean by wiping with a polished cloth slightly dipped with water. Avoid getting water inside
the unit. Do not use volatile liquids such as benzene or thinner which will damage the unit.
CONNECTIONS
Use the supplied cinch cable to connect the audio output of the CD player with a CD
input on your mixing unit.
Also connect the fader start cable if your audio mixer has fader start connections.
(Synq® or Pioneer® compatible)
Connect the mains cable.
ENGLISH USER MANUAL
JB SYSTEMS® 4/81 MCD200
CONTROLS AND FUNCTIONS
1. SEARCH Button: This button has 4 forward and 4 backward speed positions for
searching through songs. The more you turn the wheel in either direction the faster you
will search through the music.
2. TRACK SEARCH Buttons: These buttons are used to select the track to be played.
Forward skip & back skip.
3. IN/R.CUE button: Allows you to set the cue point without stopping the playback (CUE
ON THE FLY). This button also sets the beginning of a seamless loop. When you play
one of the hot cues(19), the starting point is also copied to this button.
4. OUT/EXIT button: Used to set the endpoint when looping music. The player starts to
loop seamlessly until you press this button again to exit. When a loop is programmed
but not active you can also restart the loop. The point where you press the button will
be memorized as the new end point of the loop. When the player is in “loop edit mode”
pressing this button stops the loop editing and saves the current endpoint of the loop.
5. RELOOP/STUTTER button: This button has 3 functions:
RELOOP: If a loop is programmed and you have hit the OUT/EXIT button(4), press
the reloop button to enter the loop again. Just press the OUT/EXIT(4) button to exit
the loop. (intro and end points of the loop are unchanged)
STUTTER: When a loop is playing you can press this button to restart the loop at
once. You can also press this button when a track is not playing in loop. Every time
the RELOOP/STUTTER button is pressed, it will restart the music from the
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBSystems MCD200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBSystems MCD200 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 6,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info