Manual JBSystems MCD 2.2 (page 4 of 30) (English, German, Dutch, French, Portuguese, Spanish)

468124

Zoom out

Zoom in

1/30

ENGLISH OPERATION MANUAL

JB SYSTEMS

3/56 MCD2.2

 Due to safety reasons it is prohibited to make unauthorized modifications to the unit.

INSTALLATION GUIDELINES:

 Placing and using the unit for long periods near heat-generating sources such as amplifiers, spotlights,

etc. will affect its performance and may even damage the unit.

 Take care to minimize shocks and vibrations during transport.

 When installed in a booth or flight case, please make sure to have good ventilation to improve heat

evacuation of the unit.

 To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when

bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full

performance.

 Choose the place where you put your installation very carefully. Avoid presence of heat sources. Avoid

places with vibrations or places that are dusty and humid.

 The player will work normally when installed on a surface with max. 15° inclination.

 Be very careful while handling CDs, do not touch them with wet or dirty hands.

 Discs that are dirty must be cleaned with special designed cloth and cleaning products.

 Do not use CDs that are badly damaged (scratched or deformed) they can damage your appliance.

 To prevent fire or shock hazard, do not expose this appliance to rain or moisture.

 In order to prevent electric shock, do not open the top cover. If a problem occurs, contact your dealer.

 Do not place metal objects or spill liquid inside the CD player. Electric shock or malfunction may result.

 This CD player uses the semiconductor laser. To allow you to enjoy music at a stable operation, it is

recommended to use this in a room of 5°C – 35°C.

 The compact disc player should not be adjusted or repaired by anyone except properly qualified service

personnel.

 This unit may cause interference to radio and television reception.

CLEANING THE CD-PLAYER:

Clean by wiping with a polished cloth slightly dipped with water. Avoid getting water inside the unit. Do not

use volatile liquids such as benzene or thinner which will damage the unit.

CONNECTIONS

 Connect the mini-DIN8 cable between the control unit and the main unit (CD loader)

 Use the supplied cinch cables to connect the audio outputs of the CD player with the CD or line inputs on

your mixing unit.

 Connect the mains cable.

CONTROLS AND FUNCTIONS (MAIN UNIT)

1. POWER ON/OFF switch: switches the CD-player on and off.

2. DISC TRAY: Use the OPEN/CLOSE buttons to open disc tray and put the CD in place.

3. OPEN/CLOSE button: press this button to open and close the disc tray. These buttons are disabled

during playback. If the tray is not closed after 60sec. It will close automatically to prevent damage.

ENGLISH OPERATION MANUAL

JB SYSTEMS

4/56 MCD2.2

4. CONTROL connector: connect this connector to the control unit, using the supplied mini-DIN8 cable.

5. AUDIO outputs: Output for the audio signals from the CD-player. Use the supplied cinch/cinch cable to

connect this output to a CD/line input of your mixing unit.

6. DIGITAL OUT socket: Use this connector to connect the digital signal (S/PDIF format) to the input of a

digital amplifier or digital recorder (ex. Mini disc)

7. MAINS input: connect the CD player to the 230V AC mains, using the supplied power-cord.

CONTROL UNIT

1. JOG WHEEL: This jog wheel serves 3 functions depending on the mode you are working in.

 The jog wheel acts as a slow frame search (1/75sec) control when the CD is not playing but either

paused or set to a cue point. To set a new cue point, spin the wheel then press PLAY or LOOP IN

when you have determined the proper position. Press CUE to return to the “CUE POINT”.

 If the track is playing and the fast search function (16) is not active, the jog wheel temporarily bends

the pitch of the music up to +/-32% by rotating the wheel clockwise to speed it up or

counterclockwise to slow it down. The amount of pitch change is determined by the speed of

rotation.

 If the fast search function (16) is active, you will be able to search at a higher speed through the

current track.

2. LOOP IN button: Allows you to set the cue point without stopping the playback (CUE ON THE FLY).

This button also sets the beginning of a seamless loop.

3. LOOP OUT button: Used to set the endpoint when looping music. The player starts to loop seamlessly

until you press this button again to exit. When a loop is programmed but not active you can also restart

the loop. The point where you press the button will be memorized as the new end point of the loop. In

loop edit mode pressing the OUT button stops the loop editing and saves the new loop endpoint.

4. RELOOP/STUTTER button: This button has 3 functions:

 RELOOP: When a loop was programmed and you have hit the OUT button, press the reloop button

to enter the loop again. To exit the loop press the OUT button. (intro and end points of the loop are

unchanged)

 STUTTER: When a loop is playing you can press this button to restart the loop at once. You can also

press this button when a track is not playing in loop. Every time the RELOOP/STUTTER button is

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of JBSystems MCD 2.2 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 1,47 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

JBSystems MCD 2.2 Manual

Product: