640941

JBSystems Led Rope Light Manual

4
Zoom out
Zoom in
Previous page
1/15
Next page
ENGLISH OPERATION MANUAL
JB SYSTEMS
®
3/25 LED ROPE LIGHT
INSTALLING THE LED ROPE LIGHT:
You can install the rope light easily on any surface, we suggest using the optional mounting tracks. Do NOT use lengths
over 30m, this may damage the internal conductors! When you have to install lengths over 30m, just split up the
installation in several individual lengths. With a sharp cutting device (very sharp hobby knife or wire cutter) you can easily
cut the rope light on the cutting marks ( scissor symbol every 50cm) to split it up in several parts. See “how to make a
length of over 30m” for more info!
1.
2. CUT THE CABLE AT A SCISSOR SYMBOL
3. WHEN YOU CONNECT WITH THE POWER CABLE, ALWAYS MAKE SURE THAT THE 24V
SIGN ON THE CABLE IS ON YOUR RIGHT
HOW TO MAKE A LENGTH OF OVER 30M ?
This is an example for 2 pieces with a combined length of 50m.
1. 24 V Power LED rope
2. LED Manager cable assembly
3. 4 conductor cable
4. 24 V Powercable
INSTALLING THE MOUNTING TRACKS:
Use a small hacksaw to cut the mounting tracks to the desired lengths. You can fix them to the surface using strong glue
or small screws. When all tracks are in place you just have to press the rope light in the mounting tracks. Done!
LINKING 2 LED ROPE LIGHTS:
Remove the sealing rings on both sides of the middle connector and push the sealing rings over the 2 rope light ends.
Press the 4 sharp pins of the middle connector in the 4 conductor holes of 1 rope light.
Attention: the holes and pins are a little out of the center, make sure to insert the pins in the right way and push the
middle connector as far as possible on the rope light! Put the sealing ring back in place and tighten it well. Do exactly the
same thing with the other rope light end. Ready!
ENGLISH OPERATION MANUAL
JB SYSTEMS
®
4/25 LED ROPE LIGHT
INSTALLING THE POWER CABLE:
The power cable comes together with a rope light connector that must be installed on the rope light first. Refer to the
pictures 1 and 2 below.
Attention: the holes and pins are a little out of the center, make sure to insert the pins in the right way and push the
connector from the power cable as far as possible on the rope light! Put the sealing ring back in place and tighten it well.
Ready!
1. 2.
Strip the other end of the power cable and connect it to one of the two small cable assemblies that came with the led
manager. Refer to picture 3 for the corresponding colours of the wires!
3.
INSTALLING THE END CAP:
The end of the rope light must be sealed. To make it waterproof you must put some silicon on the inside of the cap
before you press it on the rope light.
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBSystems Led Rope Light at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBSystems Led Rope Light in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 3,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info