648477
2
Zoom out
Zoom in
Previous page
1/4
Next page
2
SUBWOOFER REAR-PANEL CONTROLS AND CONNECTIONS
1) Crossover Control: This control determines the highest frequency at
which the subwoofer reproduces sounds. The higher you set the Crossover
control, the higher in frequency the subwoofer will operate and the more its
bass will “overlap” that of the speakers. This adjustment helps achieve a
smooth transition of bass frequencies between the subwoofer and the
speakers for a variety of different rooms and subwoofer locations.
2) Phase Switch: This switch determines whether the subwoofer
transducer's piston-like action moves in and out in phase with the main
speakers. If the subwoofer were to play out of phase with the main
speakers, the sound waves from the main speakers could partially cancel
out the sound waves from the subwoofer, reducing bass performance and
sonic impact. This phenomenon depends in part on the placement of all the
speakers relative to the listening position and to each other in the room.
3) Bass Boost: When switched to 'On,' this boosts bass level for added
low-end power.
4) Power On Mode: When switched to 'Auto' position, the subwoofer will
then be in Standby mode. It will automatically turn 'On' when an audio signal
is detected at its inputs, and will return to the Standby mode when no audio
signal is detected by its inputs after approximately 10 minutes. Otherwise,
subwoofer will always remain powered until Power Switch is turned 'Off.'
5) Subwoofer Level: Use this control to adjust the subwoofer’s volume. Turn
the knob clockwise to increase the volume; turn the knob counterclock-wise
to decrease the volume.
6) On/Standby LED: When the Power switch is in the ‘On’ position, this
LED indicates whether the subwoofer is in the On or Standby state.
• When the LED glows green, the subwoofer is turned on.
• When the LED glows red, the subwoofer is in the Standby mode.
7) Line In/LFE Input Connectors:
When you’re connecting the subwoofer to the dedicated subwoofer
output of a receiver/processor that has its own low-pass crossover
network, use the LFE Input connector.
When you're connecting the subwoofer to the preamp or subwoofer
outputs of a receiver/processor that does not have its own low-pass
crossover network, use both Line In connectors and set the Input
Mode switch in the ‘Normal’ position. If your receiver/processor only
has one subwoofer output you can use either Line In connector.
8) Power Switch: Set this switch in the ‘On’ position to turn the
subwoofer on.
If you will be away from home, or will not be using the subwoofer for an
extended period, set this switch in the ‘Off’ position to conserve energy.
9) Power Cord: After you have made and verified the subwoofer’s input
connections, plug the power cord into an active, unswitched electrical outlet
for proper operation of the subwoofer.
DO NOT plug the power cord into the accessory outlets found on some
audio components.
POWER CORD
STUDIO
SUB 250P
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL Studio SUB 260P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL Studio SUB 260P in the language / languages: English as an attachment in your email.

The manual is 2,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info