810178
4
Zoom out
Zoom in
Previous page
1/8
Next page
WHEN YOU HAVE COMPLETED ALL OF THE SOUNDBAR
CONNECTIONS:
1. Insert the40Afuseintothefuse holderyou installedonthe soundbarpowerwire.
2. Re-connect the vehicle’s negative (–) battery terminal.
3. Pair the supplied Bluetooth remote control with the soundbar:
a. Set the soundbar’s rear-panel power switch to On.
b. Insert the supplied battery into the remote’s battery compartment with its “+”
side UP.
c. Press the remote’s “+” button.
LISTENINGTOYOURSOUNDBAR
Turning the Soundbar On and Off
Set the soundbar’s rear-panel power switch to On. This will put the soundbar in the
standby mode. To turn the soundbar on, press the Standby button on the soundbar’s
end panel:
If your source unit does not have RCA outputs use the supplied bare wire-to-RCA
adapters to connect the source unit’s speaker wires to the soundbar’s audio input
cable, as shown in the illustration below.
2. Position the soundbar in the desired location against the vehicle mounting bar. Use
4 of the supplied mounting bracket bolts to secure each bracket top to a bracket
base. Two sets of bolts are supplied, allowing the soundbar to be mounted to
pipes from 1” (25mm) to 3-1/2” (89mm) in diameter.
a. When the soundbar is in the correct position, tighten the mounting bracket
adjustment screws as tight as possible using your fingers, then insert the
supplied small hex wrench into the holes on the adjustment screws and use
it as a lever to secure the screws as firmly as possible.
3a. Run one end of one safety harness wire through one of the soundbar’s harness
attachment loops, and use the supplied clamp to secure the wire.
IMPORTANT: Be sure to tighten the bolts on the clamp as far as they will go and
test the connection to be sure that the safety harness wire is secure in the clamp.
3b.Runtheotherendofthesafetyharnesswirearoundthevehiclemountingbarand
use the supplied clamp to secure the wire.
IMPORTANT: Be sure to tighten the bolts on the clamp as far as they will go and
test the connection to be sure that the safety harness wire is secure in the clamp.
3c. Repeat Steps 3a and 3b with the other safety harness wire, using the other
soundbar harness attachment loop and the vehicle mounting bar.
IMPORTANT: Be sure to tighten the bolts on the clamp as far as they will go and test
the connection to be sure that the safety harness wires are secure in the clamps.
Vehicle Chassis
(bare metal)
Battery
Illumination
Remote
Turn-On
Orange/White
Wire
Blue/White
Wire To illumination or
accessory circuit
To head unit
remote wire
Soundbar
Wiring
Harness
Black
Wire
Red
Wire
40A
Fuse
+12VGround
18”
(46 cm)
AUDIO INPUT CONNECTIONS
Connecting to an audio system head unit
Connect the source unit’s RCA line
outputs to the soundbar’s (black)
RCA audio input cable, as shown in
the illustration below.
Audio System
Head Unit
Front L/R
Audio Out
Black RCA
Audio Cable
Audio
Input
Soundbar
Wiring
Harness
When you’re finished connecting the source unit’s speaker outputs to the adapters,
plug the adapters into the amplifier’s input connectors as shown in the previous
illustrations.
Connecting to a mobile phone or portable audio device
Connect the mobile phone’s or portable device’s headphone port to the soundbar’s
black 3.5mm audio cable, as shown in the illustration below.
From mobile phone or
portable audio device Audio
Input
Soundbar
Wiring
Harness
Black 3.5mm
Audio Cable
Connecting to a subwoofer or secondary amplifier
Connect the subwoofer or a secondary amplifier to the soundbar’s (gray) audio output
cable, as shown in the illustration below.
To subwoofer or
secondary amplifier
Gray RCA
Audio Cable
Audio
Output
Soundbar
Wiring
Harness
GROUND,POWER,ILLUMINATIONANDREMOTE
CONNECTIONS
IMPORTANT: Disconnect the vehicle’s negative (–) battery terminal before
beginning the installation.
Connect the soundbar’s +12V power (red), ground (black), illumination (orange/white)
and remote turn-on (blue/white) wires as shown below.
Use sandpaper to clear the paint from the metal surface at the ground connection.
Use astar-typelock washerto secure theconnection.
Install a fuse holder for a 40A fuse on the power (12V) wire within 18” (46cm) of the
(+) battery terminal. Do not install the fuse in the holder at this time.
a.
a.
b.
ON
OFF
AUTO
EXT LO
HI
Standby
Button
Bluetooth
Button Page2
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL STADIUM UB4100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL STADIUM UB4100 in the language / languages: English as an attachment in your email.

The manual is 3.2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info