810176
22
Zoom out
Zoom in
Previous page
1/37
Next page
22
i. “On/Off” When set to off, the Chorus input is disabled. This allows the current signal to “ring out”
until the current Chorus signal is completed. To end the Chorus process result immediately, turn
down the Chorus Level to Mix fader.
ii. “Reset” will set the Chorus processing settings to default settings.
iii. “Presets” offers users a quick selection of common setting combinations for fast selection in typical
use cases. These Chorus presets are named as descriptions of the types of common musical uses
they simulate. The user can select “Custom” and adjust all the settings themselves. Or they can
start with recalling one of the presets, listen, and then add any settings adjustments, which will
automatically load the new combination of settings into the “Custom” setting for further editing.
. Custom
. Slow Light
. Slow Deep
. Fast Light
. Fast Deep
. Smooth Vibrato
. High Pass
. Medium Narrow
iv. “Rate” adjusts the speed of vibration of the chorus effect.
v. “Depth” adjusts the length of time the chorus process takes to ring out over time.
vi. “Width” adjusts how wide the chorus process resonates above the source frequencies.
vii. “Level to Mix” is the amount of the Chorus signal sent to the FX Return fader, which then contributes
to the nal mix.
. To adjust any parameter, navigate to the parameter using the MASTER/MENU knob. Press the
MASTER/MENU knob to access.
. Adjust the values by turning the knob CLOCKWISE or COUNTER-CLOCKWISE.
. Press the MASTER/MENU knob to accept these changes. Press the BACK button to cancel
these changes.
e. Subsynth - The FX Processing SubSynth generates a complimentary bass note one octave below the
current input music. The SubSynth effect is often used on music to add a very deep low frequency bass
effect in line with the musical source feeding the SubSynth processor, instead of a general raise in bass EQ
frequencies using EQ bands. SubSynth is relative to the incoming musical content.
i. “On/Off” turns on/off the input to the SubSynth processor.
ii. “Level to Mix” sets how much of the SubSynth result is fed to the FX Return fader, which then feeds
the master mix fader.
iii. To adjust any parameter, navigate to the parameter using the MASTER/MENU knob. Press the
MASTER/MENU knob to access.
. Adjust the values by turning the knob CLOCKWISE or COUNTER-CLOCKWISE.
. Press the MASTER/MENU knob to accept these changes. Press the BACK button to cancel
these changes.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL PRX One at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL PRX One in the language / languages: English as an attachment in your email.

The manual is 9.23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info