793353

JBL Project Everest DD65000 Manual

22
Zoom out
Zoom in
Previous page
1/26
Next page
4342
BI-WIRE CONNECTION METHOD
IMPORTANT: When you use the bi-wire or bi-amp connection
method, remove the shorting straps from the terminals (referring
to the gures below) and re-tighten the knobs on the terminals. If
the ampliers are connected to the Project Everest loudspeakers
in the bi-wire or bi-amp mode with the shorting straps still on,
the amplier outputs will be shorted, which could result in costly
amplier damage when power is switched on.
The bi-wire connection method requires one amplier channel and
two sets of speaker wires for each loudspeaker. After removing
the shorting straps, you can make connections to the individual
network sections using all four connectors, with one set of wires
to the upper (high-frequency) terminals and another set of wires to
the lower (low-frequency) terminals.
BI-AMP CONNECTION METHOD
The bi-amp connection method requires two ampliers, one for
the low-frequency transducers and one for the high-frequency
transducers, and an external dividing network (electronic
crossover). After removing the shorting straps on the loudspeaker
connector panels, wires from the high-frequency amplier are
connected to the upper terminals, and wires from the low-
frequency ampliers are connected to the lower terminals.
Each of these connection methods described above has its own
advantages – your Project Everest loudspeaker system will deliver
superb performance with any of the methods described.
FINAL CHECKLIST:
• Connect all other system electronics and plug into AC
power outlets.
• Check all connections. In case of bi-amping or bi-wiring,
make sure both shorting straps are removed.
• Make sure the system orientation and HF/LF drive jumper
bars on the control panels are correctly set.
The loudspeakers are now ready for use. The Project Everest
loudspeaker system is fully functional as soon as it is set up. There
may be subtle tonal changes in bass output over the rst week to
10 days of operation. These are caused as the movement of the
low-frequency drivers becomes more uid and the parts settle in.
This process is completely normal and natural with transducers of
this caliber. Even during this initial period, there is no restriction on
the amount of amplication that may be applied. Enjoy!
Bi-Wire Connection Method
Note: Remove Shorting Straps
Receiver or
Amplier
(one channel
shown)
Speaker
Connector
Panel
Use Both Set
of Terminals
Shorting Straps
Removed
Bi-Amp Connection Method
Note: Remove Shorting Straps
INPUT
INPUT
OUTPUT
HIGH-
FREQUENCY
OUTPUT
LOW-
FREQUENCY
OUTPUT
INPUT
Speaker
Connector Panel
High-Frequency
Amplier
(one channel shown)
Preamp/Processor
(one channel shown)
Electronic Crossover
(one channel shown)
Low-Frequency
Amplier
(one channel
shown) Shorting Straps
Removed
Use Both
Set of
Terminals
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL Project Everest DD65000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL Project Everest DD65000 in the language / languages: English as an attachment in your email.

The manual is 17.19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info