415144

JBL mr 26 Manual

4
Zoom out
Zoom in
Previous page
1/8
Next page
part of the outer insulation; or a print-
ed “+” marking on one of the insula-
tors. It does not make any difference
which of the two strands of wire go to
(+) and (–) on the speakers and
amplifier, as long as all speakers
used in your system are connected
identically. Push down on the button
below the terminal and insert the wire
through the hole.
For each channel, the red terminal on
all loudspeakers should be connected
to the red or (+) speaker connection
terminal on the receiver or amplifier,
and the black to black or (–) speaker
connection terminal (see Fig. 3).
Connecting the loudspeakers in this
manner ensures that they will be in
phase; that is, work together rather
than in opposition. This is very
important when connecting sev-
eral speakers together in a Dolby
Pro-Logic AV application. Connecting
the loudspeakers out of phase will
not damage them, but will result in
less bass and poor imaging.
When connecting the MR Center or
other MR Series speakers to a Dolby
Pro-Logic AV receiver, refer to the
instructions accompanying your AV
component for use of the “test tone”
to properly balance the sound output
from each speaker. The use of the
“test tone” and the controls on your
AV receiver will enable you to cor-
rectly balance the level (volume) of
sound coming from each speaker in
your Dolby Pro-Logic application.
Hooking Up Multiple Sets
of Speakers
If your receiver has two complete
sets of speaker terminals (“A” and
“B”), it’s possible to hook up an addi-
tional pair of speakers for
simultane-
ous
sound in another room. However,
some speakers may not be usable as
a second pair if you want to play two
sets at once. Before hooking up
another set of speakers besides your
MR Series loudspeakers, check the
following:
1. Your amplifier’s minimum load
impedance.
2. The nominal impedance of the
second set of speakers. Both of
these specifications are expressed in
ohms and both can be found in the
owner’s manuals which came with
your speakers and amp/receiver. The
receiver’s minimum load impedance
is determined by whether or not
power ratings are given for 4 ohms.
This is because two sets of 8 ohm
speakers will present a 4 ohm load to
the receiver. The MR speaker, when
combined with an 8 ohm speaker,
produces an impedance sufficiently
close to 4 ohms. For example, the
following entry in an amplifier owner’s
manual...
POWER:
A)100 watts RMS into 8 ohms, both chan-
nels driven, 20-20kHz with less than
0.02%THD
B) 160 watts RMS into 4 ohms, both
channels driven, 20-20kHz with less than
0.02% THD.
Part B indicates that the amplifier can
handle 4-ohm combined impedances
created by two sets of speakers.
4
Left
Speaker
Amplifier/Receiver
Right
Speaker
Red Blk.
(+)
++
(–)
Red
RL
Blk.
(+) (–)
Fig. 3
MR Series OM 7/28/98 10:32 AM Page 4
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL mr 26 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL mr 26 in the language / languages: English as an attachment in your email.

The manual is 0,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info