Manual JBL LSR6332 (page 19 of 24) (English)

810163

Zoom out

Zoom in

1/24

Specifications - LSR6328P

Frequency Response (+1, -1.5 dB): 50 Hz - 20 kHz

Enclosure Resonance Frequency: 38 Hz

Low Frequency Extension: User controls set to default

-3 dB: 46 Hz

-10 dB: 36 Hz

Low-High Frequency Crossover: 1.7 kHz 6th-order acoustic Linkwitz-Riley

Distortion, 96 dB SPL, 1 m:

Mid-High Frequency (120 Hz - 20 kHz):

2nd Harmonic: <0.6%

3rd Harmonic: <0.5%

Low Frequency (<120 Hz):

2nd Harmonic: <2%

3rd Harmonic: <1%

Maximum SPL (80 Hz - 20 kHz): >108 dB SPL / 1m

Maximum Peak SPL (80 Hz - 20 kHz): >111 dB SPL / 1m

Signal Input: Neutrik “Combi” XLR-G-in tip-ring-sleeve bal-

anced or unbalanced positive voltage applied to

XLR pin 2 (G" tip) produces outward woofer motion

Calibrated Input Sensitivity, XLR & G":

+4 dBu / +8 dBu: 96 dB SPL / 1 m

-10 dBV: 96 dB SPL / 1 m

AC Input Voltage: 100 /240 VAC, 50/60 Hz (auto sensing)

AC Input Connector: IEC

Long-Term Maximum System Power: 220 watts (IEC265-5)

Self-Generated Noise Level: <+10 dBA / 1 m Tonal-artifact-free noise floor

User Controls:

High Frequency Control (2 kHz - 20 kHz): +1 dB, 0 dB, -1 dB

Low Frequency Control (< 100 Hz): 0 dB, -2 dB

Low Frequency Alignments: 36 dB/octave, 24 dB/octave (VLF protection off)

Calibrated Input Sensitivity: -10 dBV, +4 dBU, +8 dBU

Boundary Compensation Settings: 0, -1.5, -3.0, -4.5 dB

Variable Input Attenuation: 0 dB to -13 dB

RMC External Bypass: G" jack

Active RMC Switch: In/Out

RMC Frequency Adjust: 26 Hz - 96 Hz (10th octave, 21 centers)

RMC Depth Adjust: 0 - 14 dB (cut only)

RMC Q Adjust: 1/20th to 1/2 octave, 21 steps

Transducers:

Low Frequency Model: 218F

Diameter: 203 mm (8 in)

Voice Coil:

38 mm (1.5 in) Differential Drive®with dynamic braking coil

Magnet Type: Ferrite, with integral heat sink

Cone Type: Carbon fiber composite

Impedance: 2 ohms

High Frequency Model: 053TiS

Diameter: 25 mm (1 in) diaphragm

Voice Coil: 25 mm (1 in)

Magnet Type: Ferrite, shielded

Diaphragm Type: Damped titanium composite

Other Features: Elliptical oblate spheroidal waveguide

Impedance: 4 ohms

Amplifier:

Low Frequency:

Topology: Class A-B, all discrete

Sine Wave Power Rating: 250 watts (<0.1% THD into rated impedance)

THD + N, H Power: <0.05%

High Frequency:

Topology: Class A-B, monolithic

Sine Wave Power Rating: 120 watts (<0.1% THD into rated impedance)

THD + N, H Power: <0.05%

Physical:

Finish: Smooth dark graphite

Handles: 2 each, flush mounted on sides

Mounting: 4 threaded mounting points conforming to

industry standard square pattern, 127 x 70 mm

(5 x 2.75 in) center to center. M6 metric threads.

Enclosure Volume (net): 28 liter (1 cu ft)

Low Frequency Vent: Rear ported linear dynamics aperture (integrated

with amplifier heat sink)

Baffle Construction: Injection-molded structural ABS

Enclosure Construction: 19 mm (G in) MDF

Net Weight: 17.7 kg (39 lb)

Dimensions (WxHxD): 406 x 330 x 325 mm (16 x 13 x 12.8 in)

Caution: Unsafe mounting or overhead suspension of any heavy load can result in seri-

ous injury and equipment damage. Mounting of speakers should be done by qualified

persons in accordance with all applicable local safety and construction standards. Be

certain to follow the instructions provided by the manufacturer of the mounting brack-

et. Before selecting a mounting bracket, be certain that it is capable of supporting the

weight of the speaker to be mounted.

Notes:

All measurements unless otherwise stated made anechoically in a 4p environment at 2

meters, referenced to 1 meter by inverse square law.

The reference measurement microphone position is located perpendicular to the cen-

terline of the low and high frequency transducers at the point 55 mm (2.2 in) below the

center of the high frequency diaphragm.

Acoustic loading provided by the listening room increases maximum SPL capability and

low frequency bass extension as compared to stated anechoic values.

Distortion measurements performed with the input voltage necessary to produce the

stated A- weighted SPL at the stated measurement distance. Distortion figures refer to

the maximum distortion measured in any 1/10th octave wide band in the stated fre-

quency range.

JBL continually engages in research related to performance improvements. New mate-

rials, production methods, and design refinements are introduced into existing products

without notice as a routine expression of that philosophy. For this reason, any current

JBL product may differ in some respect from its published description, but will always

equal or exceed the original design specification unless otherwise stated.

96 dB/1 m (Distortion raised 20 dB)

Amplitude & Phase

2nd

3rd

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of JBL LSR6332 in the language / languages: English as an attachment in your email.

The manual is 0.83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

JBL LSR6332 Manual

Product: