422470
20
Zoom out
Zoom in
Previous page
1/30
Next page
Jumper Connections
The K2 S9800 is shipped with Tw i s t e d
Pair Wire Jumpers installed between its
low frequency and high frequency ter-
minals. Please s e e Fi g u r e 9. To prepare
the K2 S9800 for bi-wire or bi-amp
operation, these jumpers must be
removed by completely unscrewing
each binding post, removing the
jumpers, and replacing the binding
posts. Wires can then be connected to
each set of terminals (s e e Fi g u r e 10) .
A m p l i fier Connections
I m p o r t a n t : Turn all amplifiers off
before connecting or disconnecting
P roject K2 S9800 l o u d s p e a k e r s .
Making connections while an amplifier
is operating could seriously damage
the loudspeaker system and void the
w a r r a n t y. All amplifiers must also be
turned off before connecting or discon-
necting cables at the amplifier or pre-
amplifier inputs.
All connections between the amplifi-
er(s) and the P roject K2 S9800 1oud-
speaker system are made at the termi-
nals located on the back of the enclo-
sure (Fi g u re 9 and 10). The left-hand
terminals (black stripe) are negative,
and the right-hand terminals (red
stripe) are positive. These correspond
to the negative and positive conductors
in the speaker wire. Each speaker wire
contains two conductors, one of which
will have a stripe, color markings, or a
r i d g e .
Assign one of the two conductors as
the negative conductor and the other as
the positive conductor. Use these same
designations for all system wiring.
Always connect the conductors of the
speaker wire appropriately to the corre-
sponding negative and positive termi-
nals on all system components. T h i s
will ensure that all components will
work together ("in phase"). Connecting
the speakers out of phase will not dam-
age them but will result in reduced low
frequency output and impaired stereo
e ff e c t .
Speaker wires may be fastened to the
terminals by several methods. T h e
most positive connection is made by
directly connecting clean, bare connec-
tors (exposed by stripping the ends of
the wire) to the terminal posts.
For this type of connection, loosen the
knobs on the terminals and insert the
exposed (bare) ends of each speaker
wire into the hole exposed on the ter-
minal shaft ( + to +, – to – ) (s e e
Fi g u re 11). Retighten the knob on each
terminal so that a snug positive con-
nection is achieved. Do not apply
excessive force and do not overtighten.
To avoid a short circuit, trim off any
excess wire that is not in contact with
the binding post contact surfaces.
20
Project K2 S9800
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL k2 s9800 s e mahogany hoogglans at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL k2 s9800 s e mahogany hoogglans in the language / languages: English as an attachment in your email.

The manual is 0,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info