Manual JBL es10 kersen (page 6 of 12) (English, Dutch)

421829

Zoom out

Zoom in

1/12

1400 ARRAY ASSEMBLY

Due to the weight of the

1400 Array horn module, it

is packed separately from

the low-frequency enclosure.

It is a very simple procedure

to install the module, and the

necessary instructions are

listed below. The required

Allen-tipped screw driver is

included in the accessory

pack.

1. Carefully remove the horn

module from the packaging

and place it face down on a

soft surface.

2. Locate the cardboard

accessory sleeve and

remove the hardware.

3. The accessory sleeve

should contain:

a. 2 Long 1/4" x 20 Allen-

head bolts

b. 1 Short 1/4" x 20 Allen-

head bolt

c. 1 Logo plate

d. 1 Rubber hole plug

e. 4 Metal coasters

(to protect wood and tile

floors from the spike feet)

4. Carefully unpack the low-

frequency enclosure and

place it upright. It would be

helpful to position it near its

final position in the room

since it is much easier to

move without the additional

weight of the horn module.

5. Notice the two threaded

inserts on the angled face

of the top and also the small

L-bracket on the top. These

are the attachment points

for the horn module. Imme-

diately adjacent to the L-

bracket is a recessed con-

nector which will make the

electrical connection for the

horn module.

6. Although the module can

be installed by one person,

it is easier if a second set

of hands are available.

7. Cradle the horn module with

the opening along your fore-

arm and, using your free

hand, connect the plug

coming from the bottom of

the horn assembly into the

jack on the top of the

enclosure.

8. You can now place the horn

in position on top of the

enclosure. The L-bracket

fits in an opening under the

horn assembly. The module

will sit on top of the enclo-

sure by itself, although it

should always be steadied

until fully mounted.

9. Line up the two mounting

holes on the lower lip of the

front of the horn with those

in the enclosure. Partially

install one long bolt and

then the other one. It may

be necessary to lift the horn

slightly so that the bolts

install smoothly. Do not

force or cross-thread them.

10. Once both bolts have been

started, work them in all of

the way, but do not tighten

them securely just yet.

11. Install the remaining short

bolt in the hole at the

bottom rear of the horn

module. You can fully

tighten this bolt.

12. Now completely tighten the

two front bolts.

13. Everything should be tight

and properly aligned at this

time. If not, loosen, realign,

and retighten as required.

14. The final steps are to

remove the backing from

the logo badge and place it

in the recess on the lower

horn lip, and to use the

rubber hole plug to hide the

hole at the bottom rear of

the horn module. Do not

complete these steps until

the system has been turned

on and tested acoustically.

Make sure the horn module

is playing first. Once the

logo badge and rubber

plug hole are installed, it

is extremely difficult to

remove them.

Project Array OM 1/10/06 12:21 PM Page 6

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of JBL es10 kersen in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

JBL es10 kersen Manual

Product: