810142
7
Zoom out
Zoom in
Previous page
1/14
Next page
INPUT
LEFT
RIGHT
AMPLIFIER
4Cl
PER CHANNEL
6.n
EACH CHANNEL
--
SerieslParallel
-
It is possible to utilize various serieslparallel 'hook-up' topologies to increase the number of loudspea
driven on an amplifier. See diag. 4 for one example of a serieslparallel hook-up topology.
Note: Mismatching the speaker impedance such that it is below the minimum impedance rating of an amplifier channel
damage the amplifier and degrade performance. If the application requires more than
2
speakers per amplifier channel
wired in parallel, a distributed line system should be considered. Also check your amplifier's manual for cautions and
recommendations.
Importance of Correct Polarity ("In-Phaselout-of-Phase")
-
When two loudspeakers are wired with opposite polarity
("out-of-phase") relative to each other, the low frequencies of the loudspeakers cancel each other, even though the speak-
ers are "working hard." Trying to correct the lack of bass with an equalizer can damage your loudspeakers
--
equalization
cannot correct polarity errors. Always make sure multiple speakers are connected in proper polarity. (See "Poor Low
Frequency Output" in the Troubleshooting section for instructions about how to detect and correct polarity problems.)
-
Distributed Line Systems (Control
"AT"
models)
-
The Control@ 25AT
&
Control@ 28AT models come equipped with
in 7011 00 volt autoformers.
These types of speakers need a line distribution amplifier.
As with conventional 8Q s
ers, simply connect the amplifier's
"t"
and
"-"
outputs directly to the red (t) and black
(-)
input jacks on the back of the
enclosure. Set the autoformer tap to your desired wattage. Unlike conventional 8fl speakers, you may connect as many
"AT" speakers as you'd like to one amplifier channel
providing that all the speaker taps do not add up to
more
than the
amplifiers power rating
(see diag. 5).
(e.g. A 100 watt amplifier channel could safely drive 13 speakers set to 7.5 watts each, i.e. 13 x 7.5
=
97.5
<
100) A
conservative rule-of-thumb is to try to keep the sum of the speaker loads (watts) under 314 of the power amp rating (e.g. A
100 watt amplifier channel will then drive 10 speaker set to 7.5 watts each, i.e. 10 x 7.5
=
75 watts).
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL Control SB-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL Control SB-2 in the language / languages: English as an attachment in your email.

The manual is 2.06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info