809541

JBL Control One AW - Control 1 AW Manual

3
Zoom out
Zoom in
Previous page
1/4
Next page
3
www.jbl.com
English
A. Loosen and remove the molded nut (2) by turning it
counterclockwise. Use the supplied metal bar (5) if necessary
by inserting it in one of the holes on the molded nut (2).
B. Pull the ball/shaft (3) out of the wall bracket (4).
C. Slide the molded nut (2) onto the ball/shaft (3) with threaded
opening facing the ball, and thread on the metal nut (1) all the way
onto the ball/shaft (3), with the nut’s (1) “knurled” surface facing
away from the ball.
D. Screw the ball/shaft (3) into the threaded 1/4"-20 insert (6) on
the back of the speaker cabinet until it is fully seated against the
bottom of the insert. Back out the ball-shaft assembly one half
turn and tighten the nut against the speaker. If the ball and shaft
assembly is not backed out before tightening the nut, performing
Step G below may dislodge the threaded insert in the speaker
housing and permanently damage the speaker.
E. Tighten the “knurled” nut (1) using a crescent wrench until it is firmly
seated against the back of the speaker and has fully locked the ball/
shaft (3) and the speaker cabinet together. Please note that once
this nut is tightened, it may embed some marks on the back of the
speaker where the attachment is made. However, these marks will
be covered by the nut (1).
F. The backup cord (8) is provided as an additional measure to prevent
the fall of the speaker in case the speaker becomes detached from
the wall bracket. One of the two lower screws (9) that attach the
wall bracket (4) to the wall will need to go through the eyelet (11)
at the end of the cord before going through the wall-bracket hole.
Make sure that the screw head is at least 0.36" (approximately 3/8")
or larger in diameter so that it can properly hold the backup cord
eyelet (11).
G. Mount the wall bracket (4) onto a wood stud on the wall, using #10,
minimum 1", panhead wood screws. Make sure that all four screws
are driven into the stud, not drywall.
If the bracket needs to be mounted on drywall, the use of properly
selected and installed wall anchors and screws is essential.
H. Holding the speaker cabinet (7) with both hands, reinsert the ball
portion of the ball/shaft (3) into the wall bracket (4).
I. Hand-tighten the molded nut (2) while positioning the speaker for the
intended orientation.
J. Once the orientation of the speaker is finalized, use the metal bar (5)
in one of the holes on the molded nut (2) and tighten securely.
K. Securely attach the other end (10) of the backup cord (8) to the
Control One AW by engaging it through the bar (12) on the back
speaker, as shown in the illustration.
Please note that while the JBL Control One AW is an all-weather
outdoor loudspeaker, it is not waterproof. The speakers should NOT
be submerged or directly exposed to water, ice, snow or sustained
moisture.
TO LEFT SPEAKER
+–
TO LEFT SPEAKER
+–
CORRECT INCORRECT
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL Control One AW - Control 1 AW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL Control One AW - Control 1 AW in the language / languages: English as an attachment in your email.

The manual is 0.71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JBL Control One AW - Control 1 AW

JBL Control One AW - Control 1 AW User Manual - German - 4 pages

JBL Control One AW - Control 1 AW User Manual - Dutch - 4 pages

JBL Control One AW - Control 1 AW User Manual - French - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info